Has anyone tested rocket dump on BMW EDC16? I've got a licensed version but it doesn't seem to work, I'm not sure if it's a bad solution, or if the customer is doing something wrong.
Do we need the EWS module plugged in?
Does anyone have a complete IMMO OFF solution through the eeprom, the solution I am using says it's to be used on the processor file, however if I add the external flash file it also still processes the file.
I have tried solutions 1 and 2 from rocket dump in the following configuration:
Processor only v1 Processor plus flash v1 Flash only v1
Processor only v21 Processor plus flash v2 Flash only v2
All tried with AND without EWS plugged in, however I think the EWS is from a different car.
That leads me to believe that if we had a full IMMO OFF solution from the eeprom it would probably start even if EWS is not connected?
Hello, i have problem after odometer correction i get oil service -99000km on dash. Bsi set to 0 and service history is reset. Dash is disconnected when I connect the bsi. all seems ok, but when i stop engine close car, and comeback after 5-10min it come back again -99000km and on dash i see wrench icon. what to do?
I would like to buy an ALLDATA EUROPE online accountwhere users have a separate, independent account.
If anyone has access to or sells one, please reply or send me a pm.
Thanks.
Hello friends. I am trying to figure out how to get 4 digit pin from this label. Google did not help me.
This is what I got:
SIEMENS 28 590 C9965
Made in Mexico
5WK4 8043C 51677C
電波91LP0158
Nissan BSVU17 STEP 6 f-125kHz
on the Skoda Octavia IV Vin. TMBJR8NX4SY064142 I need to ODIS FOD/Swap + SWK for manually removable towbar with 1M5 preparation. The towbar is not original and I can't find this code anywhere on Elsa. Thank you in advance for your help
Hello, i have this Golf 7 under water, not cranking with several errors on ecu, gateway bcm!
I want to start cloning these parts and want to start with bcm
I need to know what tools to prepare to do this remote!
I have a vas clone installed and some other tools ...
probably will follow gateway and ecu..
Autohex II Professional programming option AHX004.
Current price from Microtronik is £3200.
Selling for £2200 including free shipping worldwide.
Contact in PM if needed.
Background:
1. I attempted to reprogram a 2007 Audi A6 C6 to add a key.
2. I utilized OBD Star - Key Master G3 for this purpose.
3. During the process, the car entered sleep mode, resulting in a failed attempt.
As a result, the car lost its key settings.
4. I then tried to retrieve data from the EPROM using Launch Pro 3 (Screen 1, 2 + Launch Pro 3.txt).
5. Unfortunately, it appears that this file has become corrupted.
How do I restore this file to its original state? Or is it possible to create the correct one using VIN?
Alternatively, do you have any suggestions on how I can revert the car to its original state?
Hello.
Last summer I bought a 997.2 with a faulty PDK.
After changing the distance sensors and a complete overhaul of the PDK, the TCU was deprogrammed in the calibration process. With Flex from Magicmotorsport in bootmode we managed to program it with the fullbackup of the Cayman S, the car now starts and lets you move the lever, but it does not read correctly the data from the sensors, P1731 faults appear that cannot be deleted, and it is not possible to perform the calibration with Piwis.
Please, I need the fullbackup of the pdk3000 997.2 C2S (2009), can anyone help me?
The TCU data is as follows:
It looks like my airbag control unit has locked itself. The error memory shows "component protection," even though it's the original control unit from my car.
A colleague and I, both Mercedes specialists, are trying to activate the Blind Spot Assist on a 2022 Mercedes W447.
However, this has proven to be quite challenging.
The car was originally delivered with the J0V option (Preparation for Blind Spot Assist). We have installed the original rear radars and replaced the mirrors with ones that include the warning triangle.
We have already coded the IC, left door, right door, EZS, and Parktronic (Variant Coding).
Despite these efforts, we still cannot determine the necessary codings to activate the system. And we cant get it on the menu of the IC (IC447KIG2).
According to the WIS documents, we need to edit VeDoc to remove J0V and add JA7. However, we do not have access to VeDoc, and this seems impossible.
Has anyone here encountered a similar issue before?
Hi everyone , need help with pops and bangs SDI4 . I have a problem with total 0 result .
I have changed ignition maps , fuel resume , try many others maps but tottaly 0 result.
Can someone help me with this?
Thanks for attention and help.
Not for free , payment after test.
![[Image: 3dd425b0-2cdf-4750-be95-0d1bcb5be12a.jpg]](https://hosting.photobucket.com/ea20d1db-d327-4a7c-a9dc-5aeb5ede45c7/3dd425b0-2cdf-4750-be95-0d1bcb5be12a.jpg)
![[Image: fd09e490-da6a-407f-9db3-7d4b70a9555e.jpg]](https://hosting.photobucket.com/ea20d1db-d327-4a7c-a9dc-5aeb5ede45c7/fd09e490-da6a-407f-9db3-7d4b70a9555e.jpg)
![[Image: 3da3fe60-dc6c-4eb1-99c3-b9796017b95b.jpg]](https://hosting.photobucket.com/ea20d1db-d327-4a7c-a9dc-5aeb5ede45c7/3da3fe60-dc6c-4eb1-99c3-b9796017b95b.jpg)
![[Image: 20250127-171716.jpg]](https://i.postimg.cc/7bphbWwP/20250127-171716.jpg)
