What eeprom i must read to make immo off? I have see that this type of ecu people removes green part (image). Could you correct me, what need to do? After immo off need to remove connector from the immo coil? on board see that is eeprom 93LC46B, on green board not see eeprom. or need emulatoras I found in one file (image)?
hello, im trying to use odis online service v24.1 and when im trying to scan it ask me to login with a GRP account and i dont have one how do i procced with this and if im trying to register an account it ask me for a BID/partner code
Could somebody make me an immo off please for these ecu?
The car worked without any problem but made a software upgrade and after no start the engine and immo activated on the dash, ecu closed.
It seems the ecu was an aftermarket used ecu so maybe was an immo off on the system.
Dear all,
My CGDI MB is not working and now is chinese new year in China so no one give support now.
Thus, please help to get erase password of ECU SIM271DE20, with special key : 25 B6 BA 33 3E CE B3 00.
Thanks in advance for your assistance.
Business is a little slow in the local world so I thought I can try and offer my services here.
I can do immo matching on most VAG ECU, TCU, ELV and BCM (Matching used donor unit with car if you read both, Or matching to IMMO ecu in car)
DTC off in most ECU
EGR, DPF, SCR , Swirl and etc off on most Bosch ECU but mostly VAG and other German cars
All manual solutions
I can also offer Tuned files, But in my previous experience no one wants to pay for actual manually made files but if you are interested in tuning without mass copy paste and decalibration please write me an email
Prices
Immo matching : 30-100€ (Depending on car)
DTC off: 10-30€ (Depending on ECU and how many fault codes)
EGR off: 15-30€
DPF off: 20-35€
Swirl off: 10-15€
SCR off: 40-60€
You yourself are responsible for having compatible and functional tools
If you send an email, Please write down Brand, Model, Year, ECU model and what you want done
Working a C216 Mercedes-Benz CL 500 2007 model. (Same as w221 sedan)
Vehicle was slightly flooded at some point.
I replaced ALL the Can block connectors on the vehicle under the carpets so now it starts and drives, AC and radio working properly.
Only issue that I'm still trying to figure out is the EPB (Electric parking brake).
I got the yellow P sign on the cluster, and "Parking brake inoperative" message on the cluster.
I cannot active or deactivate the parking brake using the button/switch.
Went through test procedures, and confirmed the module under the car is still fine as I was able to operate the parking braking using a diagnostic machine.
The only error code on the parking brake module is " Check component parking brake switch" current and stored.
I tried to replace the parking brake switch twice even, but still no joy.
I would like some assistance with information of the signal path for the electric parking brake between the module and the switch.
Hello guys, i will post this thread here too, because i did not solve the problem so if anyone can help out. So when i put the ecu in without IMMO OFF flash the car starts and shuts down on the key. So i have crank and start. When i put the flash with IMMO OFF the car will not crank or start on the key. Only if i hardwire it on the starter the car starts.
Can anyone help out with this situation, thank you all, with respect
The car shut down while driving, there is no fault whatsoever
I start it on the spray and it runs on the spray and reports low fuel pressure
I put injectors, high pressure pump and rail branch with sensors, but the car does not start, has anyone had a problem like this?
This program will help you learn back the password of the vems operating system computer you purchased if you have forgotten it.
Remember that you are the owner of every product you purchase. There is a password specific to you for each serial number. In order to download and run the application, you need to turn off defender real-time protection. Dotnet 8 windows package must be installed on your computer for the program to work.
Hi all. I have VXDAS VAS6154A and original Odis E version 18. It was working fine for a few months but now it stopped working. Odis E can not see it. I tried my VAS6154A with another computer with cracked Odis and it works fine. Anyone can help?
hello, can someone help with reading rcd 210 panasonic mcu M30897fk, I connected it as per orange 5 diagram , it begins to read and than says read error. tried to change baud rate, and connect 12 volts to power the unit, and always the same
![[Image: 1-Main-Windows.jpg]](https://i.ibb.co/VYsgQVpJ/1-Main-Windows.jpg)
![[Image: 2-Audi.jpg]](https://i.ibb.co/NgfhV5ZT/2-Audi.jpg)
![[Image: 3-Commercial.jpg]](https://i.ibb.co/35MyDhmB/3-Commercial.jpg)
![[Image: 4-Onibus.jpg]](https://i.ibb.co/QjvJ72X1/4-Onibus.jpg)
![[Image: 5-Porsche.jpg]](https://i.ibb.co/wr7jNJc2/5-Porsche.jpg)
![[Image: 6-Seat.jpg]](https://i.ibb.co/LDMDQmb2/6-Seat.jpg)
![[Image: 7-Skoda.jpg]](https://i.ibb.co/mV2hZPT1/7-Skoda.jpg)
![[Image: 8-Volks-Wagen.jpg]](https://i.ibb.co/23sRtv1Z/8-Volks-Wagen.jpg)
![[Image: 9-Main-Group-Select.jpg]](https://i.ibb.co/xqnKLXsQ/9-Main-Group-Select.jpg)
![[Image: 10-Part-Number-Select.jpg]](https://i.ibb.co/KzbHRZvr/10-Part-Number-Select.jpg)
