Hello Guys i’ve problem with Dacia Duster 2012 year. Uch have damaged blinkers and lights . I’ve bought new Uch from Renault with newest available Part Number (8201497785) and want configure it in car by Clip , but it wants from me write security Key . I’ve read ISK from old uch by ddt2000, recalculate it using renault clip tool to Pin Number but it doesen’t work , code is wrong.
When i press uch learning procedure on clip , program generate long code and it want to write another security code under . Is there any other way for do this?
I am trying to solve kessy issue which unfortunately got flooded. So the easiest solution that came up is controller swap with new old kessy module.
Here is the trick, PIN code retracted from EEPROM brick of it is being constantly rejected, that would mean that my calculated PIN is wrong or there is some other problem too.
Could someone take a look at attached damp files? All are from same memory just read with different software setup (I am completely newbie). Device used to read it was TL866 if I am not mistaken.
Cracked by me PIN is 04422, the rejected one...
Probably an odd thing to ask but I have heard a lot of people mention a guy that cracks all the softwares and then sells reseller privileges to other folks. Just wondering if anyone knows who this is or if someone could PM me his name.
Hello everyone, i am dealing with a 2018 bmw m4 and the rollover bar opened up during accident. How can i put this back? i read manual it says pull red tab, push down 10cm then push the bar down but it wont lock in place. Anyone dealt with this? It should be the same as 4 series from 2014-2020. Do i need to replace the whole unit? I know in the past there were little piston we would replace
[font="MHH Font", Calibri, sans-serif]can sombody make stage 1 for this file?[/font] [font="MHH Font", Calibri, sans-serif]MB crd2[/font] [font="MHH Font", Calibri, sans-serif]read with fgtech by obd[/font] [font="MHH Font", Calibri, sans-serif]Dpf is off, but i dont realy understand very well this ecu's yet....its the first one to make a stage[/font]
[font="MHH Font", Calibri, sans-serif]Thanks in advance[/font]
I have recently purchased A4 B9 Avant 2016. The car was damaged, I got the airbag sensor repaired + new hood hinge actuators installed as they deployed.
I see two errors that I'm unable to clear:
Code:
2 Faults Found:
9449984 - Pedestrian Protection Crash Sensor (driver's side)
B1032 00 [137] - -
MIL ON - Confirmed - Tested Since Memory Clear
Code:
9444115 - Front Passenger's Front Airbag Crash Sensor
Code:
B101B 15 [137] - Open or Short to Plus
Code:
MIL ON - Confirmed - Tested Since Memory Clear
The sensors are all checked, each time I unplugged one I saw a new error, then I was able to clear it. But those two are always present. Is there a fault with the airbag sensor?
I attached photos of the sensors that I checked. The actuators (hood releases) throw a different error when unplugged.
Hello , i lives in poland and have a problem with the car of my wife asx 1.8 DID
what is the problem, the car has problems with canbus b error code u0184, everything works only every 4 seconds I get a beep signal, the car was purchased with an after market radio without canbus, and without a canbus module from the Alpine brand, it worked for 12 years without any problems, so in my opinion the variant coding was changed to audio can not be active, now I am looking for someone in the province of Pomerania Poland who can recode the etacs, there are programs that can do that such as mmcodingwriter or etacs decoder, I only need it once, please send a message in pm
I was scammed by a person on the forum with the username andreas.schmidt. He asked me for an advance payment, which I made through Revolut. He tried to make the file but failed. He didn't return my money and he doesn't answer me. I think everyone should see this. I'll upload a Skype conversation later.PLEASE REPORT.....
(01-30-2025, 11:50 PM)techcar1992 Wrote: I was scammed by a person on the forum with the username andreas.schmidt. He asked me for an advance payment, which I made through Revolut. He tried to make the file but failed. He didn't return my money and he doesn't answer me. I think everyone should see this. I'll upload a Skype conversation later.PLEASE REPORT.....
this is first message- Hello. Yes, possible on sport mode but not free. Can you contact me on mail: [email protected]
techcar1992 Wrote: Wrote:email...give whatsup
I dont use whatsapp. Skype: live:.cid.225c1e929397d131
