Hi, I have a tune file, that works perfect on automatic 218hp e60`s, (euro4)
But in a manual car, everything is okay, except engine fan runs 100%.
Because there is no temp signal from auto gearbox.
Possible to fix this?
Hello, I need the original bensch file. They brought me a Mercedes Vito 114 cdi 100kw eu5 rv 2016 for repair.ECU A6519002803 Bosch 0281031244 The obd cable fell out while recording with the autotuner. AFTER recovery obd not working. I read Kess bench but I don't have this software. Please help me.If it is possible to repair the original fleas MPC bench, which is almost completely deleted, I will be happy. But I need a bench backup.I'm happy to pay
ID obd kess HW:6519012802,SW:6519022804,SW upg.:6519037685
I have a Fiat Doblo 1.6 88kW with EDC17C69 ECU from 2020.
I've tried several versions already (Deluxe, Swiftec, etc.), the outcome is always the same: the car runs at 950rpm with massive white smoke. With ori, the idle is 850rpm and there is no smoke at all, but dtcs for DPF.
I'd appreciate a 100% working DPF off solution, read is attached.
First i thought was blocked injectors, swapped for a second hand set, as soon as i did engine started ran.. soon as i turned it off back to the same fault - Ive also swapped the pump just as i had known good parts from an old engine about
Connected injector to rail (injector not in cylinder head), cranking definitely no fuel from injectors
Cloned engine ecu, still the same
Any ideas what would cause ECU to not fire injectors? Or what are the reasons on this ECU they do not get fired and i can re check from there
Coolant levels, temp readings in live data all look ok
Need help for my e350 cdi , want to turn off egr but to still be able to use dpf for regeneration , searched for mappack or damos but couldn't find.
If someone have mappack/damos will be great or at least egr off. I can pay for help.
I'll add the ori which i read.
Thanks for help.
I have cracked clip v202 installed on a w19 64 laptop that I use with Bosch RNM VI3, does anyone know if I can download and run official Renault ADT software in the same partiton? ?
Is there anyone out there who can give me the pinout on the magpro obd to eth. I dont have any cable so would be great if someone could help me.
Magicmotorsport dont have the cable anymore so cant buy it
If anyone has had or has a dashboard handy from Audi A4 B8/B9 I want to know on this area (ACC - Adaptive Cruise Control) all 4 led-s are present ? What colors ?
My dash is 8K0 920 930 D, Magneti Marelli 2010 and these LED's are missing.
I recently had to replace an faulty ecu which was not available so a ecu kit was obtained, everything works apart from dash warning about rear doors open, the kit came from a full van but the vehicle is a flat back tipper so no rear doors, got the as built but the options to delete the rear doors only gives different errors about passenger doors and boot if changed, i have both as built data for new ecu kit and original setup, is there any way to transfer the data from original as built to new kit and reflash the correct data, the vin now shows from the replacement kit, the bcm i beleive contains security and key data so a simple clone of software wont work, any help appreciated and thank you in advance.
I’m looking for assistance with resolving a Component Protection (CP) issue following a dead battery/jump start on my vehicle. Due to my location, the nearest dealership is a 5-hour round trip, and I’m hoping to find someone who can help me perform this remotely.
Vehicle Details:
Make: Volkswagen
Model: Jetta
Year: 2023
Modules affected: Body Control Module (BCM) and Gateway Module
Issue Summary:
The vehicle is showing CP-related faults, which are causing reduced functionality. Based on my understanding, this can be resolved with a CP reset/matching process using ODIS connected to Volkswagen’s factory database.
A developer of the Comma AI community passed this feedback to me:
Quote:@Ignored There are no physical faults and no missing modules, only CP faults. Take your car to a different VW dealer and tell them you need component protection reset on your BCM (address 09) and your gateway (address 19). The addresses won't really mean anything to them, but BCM and gateway will, and they'll figure it out. It has to be done with ODIS with a connection to the VW cloud. Here's a video of what they need to do:
If CP-protected control modules think they've been transplanted between cars or otherwise lost their anti-theft identity, they go into a lower functionality mode. The driver-visible misbehavior you're seeing is intentional when CP is active. It's meant to discourage people from stealing your car to sell for parts. To fix them, there's a crypto/key exchange with VW's factory database, and a check to see if that module's serial number originally left the factory in a car that's been reported stolen.
What I Have:
Access to the vehicle logs (attached to this post).
I’m willing to purchase the necessary hardware (e.g., a clone VAS5054) if someone is able to guide me through the process or connect remotely to assist.
What I Need:
Assistance from someone experienced with remote CP matching.
Guidance on any tools or equipment I need to purchase before proceeding.
If you’re able to help or can point me in the right direction, I’d greatly appreciate it.
Hi guys, i need someone who can do EGR DPF off with checksum. ( with egr connector disconnected please )
For all others, i upload free full ktag backup (seperated and in one file) for those who fucked up their ecu.
This ecu i read in other forum is totaly fucked up if u dont know how to read and write. i dont want to brick that ecu.
i managed to read, but i dont want to do any mistakes. so if someone can do a howto write this ecu i would be very happy.
thanks in advance
for those who dm me to earn some money, im looking for free solution dont dm me please.
Money is not everything im helping others also without taking any money
model year:2015
engine:2.4L diesel D3
power:181 horsepower
ecu diagnostic part number 31321233
hardware partnumber 31321233 AA
hardware serial 125521715024
software part number:31491384 AA
vin: YV1FW8156F1262518
calibration identification 1 : 31491384 AA
calibration identification 2 :31372679 AB
calibration verification numbers 1 : A204CBA8
calibration verification numbers 2 : D2E4D283
thank you
Hello. I have a broken Volvo V50 control unit 2.4 140 hp built in 2004. I would like to buy a used one and clone it if the old ecu is still readable or make immo off.what nummbers of ecu must be the same?to buy the right ecu.Haven't done Volvo yet.Thanks
hello
i have buy opcom 2022 but it dont work
the software is cracked by fantomel
i have problèmes drivers for win 10 64 bit
i have test on another same pc WIN 10 64 the probleme is same
some one have a solution please
thank in advance or good drivers
best regard
