Hey friends I’m having issues with this 2014 ML350, I replaced the vgs unit with a used one that had the exact same part number (A 003 446 03 10) but I’m having issues putting the session into reprogramming mode I have successfully gotten the seed key and it accepts it but nothing for programming mode.
I’m using vediamo 5 and a C4 if that helps
If anyone could help or advise i can pay if necessary
motor for sunroof and control module for sunroof brand new. Keep getting ERP error when coding with ODIS.
Original odis and grp.
Has anyone encountered similiar/same problem?
Regards
hello, I have here a vw tiguan 2014, with electric parking brae problem. The right rear epb motor stopped working
with dtc 02433 supply voltage for right parking brake motor v283 007 short to ground
fuses checked, another motor installed, wiring tested for shorts and loose connection, all seems ok
I suspect the epb module 3AA907801J,
does anyone have mc9s12xd256 flash and external eeprom 25320 for this ecu?
Have two weeks trouble with w221 350cdi . i measure 4.5Amps battery drain for one night with new pulled battery. After lot of search, wiring diagrahms i took a drain goes out after i remove one of two fuses.
1. Central gateway
2. Electric parking brake
Change two components - still have same drain. On diagrahm see have CAN there - try unpluged one by one all i have seen / upc,ic,command,ezs,parking switch / - nothing changed???
See a bulletins for drain - update upc panel , try to remove front fan - without sucssess.
Posted by: jointdmc - 01-24-2025, 09:21 AM - Forum: Selling Box
- No Replies
Dear all Member
I support Programming when replacing a new Unit, used Unit for Toyota Lexus cars (SRS, EMPS, Engine, Rada, ...)
If you want to do it quickly and reliably, please contact me via WhatsApp . I will help you faster.
PRICE : 50$ - 150$ All model Toyota/ Lexus.
CAR INFORMATION:
Brand: LAND CRUISER LC300 GCC Year: 2022
Model code: VJA300L-GNUAZV
Information on EPC
BEFORE: Many Warning light turn ON and car can not start
AFTER: All Warning light turn OFF and car can start
All services are in the attached txt file.
Please contact me viaWhatsApp (informations find contact in my profile)
For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes.
First gen Bentayga, lights converted to have Amber blinkers, need to separate blinkers from brakelights.
I have ODIS-S and ODIS-E, I cannot find anywhere in ODIS-E the coding variant to disable SAE lights, or to change taillights to RoW in any of the modules, 009,046, etc; most of my familiarity in VAG is Porsche, so in PIWIS3 it was a simple as uploading ZDC and modifying the PR codes, took 5min.
Whats the procedure in OTIS? or do I have to get VCDS?
Hello, has anyone else had issues writing a L21-L23 ecu with a Kess3? I have had multiple that will read fine and then at the end of writing the mod file, it gives an error, then asks to do recovery. I select yes to do recovery and then it says error again and states that the protocol does not work with this ecu. Alientech has been of no help the last three times. Luckily up until now I've been able to ultimately recover them eventually and then re read and write using Dimsport. This current machine, however, will not recover or reprogram even with service advisor.
Hello, is there anyone who can correctly convert the engine controller software from a semi-automatic gearbox to a manual gearbox in a 2011 107kw 150hp master, I am not looking for a free solution, but finally a working solution (still no starter control)
Best regards
I installed Xentry Openshell 2021.6.4 following this guide https://mhhauto.com/Thread-How-i-got-Xen...-3-to-work
Everything is fine with the Startkey, however, when I want to start Xentry Diagnosis, the following window appears. I have not seen anyone else with a similar error. Does anyone have any idea what it could be?
It should be noted that I had previously installed the same version on another PC with the same instructions and it worked without problems.
I need to code a power steering on a 2018 Skoda Octavia... this car arrived at our workshop with a yellow light on the dashboard with the steering wheel symbol... but it does not have any stored DTCs... I'm a little lost with the topic and I would need someone to code it for me with ODIS online... is there anyone available to code remotely???? thanks
Someone who can help me stop the fan on the mazda 2 denso control unit.
Set egt 600°C probes, if I put third probe under 380 does not start fan but accumulates pm, if I put on it it stops fan but does not accumulate pm. Does anyone help me? Thank you.
A few months ago, I had a car on which a local mechanic worked on the EGR and DPF, but the job wasn’t done properly. The car had an error indicating an issue with the turbo, specifically the turbo actuator. After thorough investigation, I sent the map for inspection and was informed that the EGR and DPF weren’t properly disabled. I received a corrected file, wrote it to the car, and everything worked fine afterward.
Similarly, for the past 2-3 months, my uncle has been experiencing a similar issue. Many components have been tested, and he also had the EGR and DPF done by the same person. He frequently encounters a problem indicating a turbo actuator fault. Despite visiting several mechanics, no one has been able to identify the issue, and many parts have been replaced. I’m wondering if it’s possible that the EGR and DPF weren’t properly disabled again. The car also has a Stage 1 tune.
I’ll attach the map and the current error code related to the engine. There are no other errors related to this issue.
It's a Citroën C5 2011 1.6 82kW.
Error:
P2566 Variable Geometry Turbo - Excessive Deviation from Upper or Lower End Position in Recent Learnings
Map:
I am looking for Firmware: 4.036 for kess
I have just been given 2 kess v2 boxes which were connected to the internet for updates and of course you really shouldn't do that.
I am looking for this firmware in order to reinject it into these boxes to revive them.
I've been browsing the internet for 3 days without success, all the links I found are dead.
(if you even have another firmware, let me try a repair)
thank you very much for helping me.
hi
i need help with 2017 mf moto cforce 550
i need to remove speed limiter
its bosch mse6.0
i did read it obd via autotuner ,
my firest atv , i usuwally work with car
much appreciated
Someone tried to make a new key.
The new key worked 3 times.
After 3 time the car didn't start.
Accidentally the ori key was erased. Now both keys not working. Immo flashing in dash.
No communication with immo module.
Tried an immo off solution by connecting a couple of cables in ecu and immo antenna.
Not working.
Can't adapt new key either.
Seems like sth is locked.
Is there an ecu eeprom virgin solution?
Carlabimmo is giving a solution for 0261201253 ecu. Can anyone with access take a look?
Thanks!
I have Autel Maxi Pro MP808 tablet.
I would like to change stock app for diagnose for another one. Subscription is ended and a lots of features is off.
This is who i need to change diagnose app for other.
Hello, I am looking for original full bdm for Nissan Quashqai 2.0dci J10 2010year , automatic transmission. If can DPF off will be perfect. ECU: 0281014858 Because now i flashed some file with software 1037398977 but I don't know its for Auto or Manual transmission, now car start but stuck in gear and not shifted. ( File 98977 original).
Every time I start the car, I keep getting the message "Front-passenger airbag disabled. See Owner's Manual" on the instrument cluster. The Occupant Classification System (OCS) is working fine, as the message changes to "enabled" when a passenger is seated. However, it's quite annoying that I have to press the "OK" button on the steering wheel to clear the message every time.
Is there a way to permanently remove this message, perhaps through coding in Vediamo or any other tool? Any help would be greatly appreciated!
Hi,
I have abs controller 3452 6776067 01 and I found another one with exactly the same PCB 3452 6778239 01. My question is, can I write flash file in 3452 6778239 01 from 3452 6776067 01? If yes which tool should I use?
I do that with vw Mk60ec1, but BMW is now for me.
Hi i have corvette c7 usa, changed speedometer disc from vmax scale to 360 vmax disc. When i have metric set it shows correct speed but i need metric units and correct speedometer. Does anynone have solution for this? Original and mod speedometer disc in attachments.
![[Image: UAxl7L8.png]](https://i.imgur.com/UAxl7L8.png)
![[Image: 1DhFDv6.jpeg]](https://i.imgur.com/1DhFDv6.jpeg)
![[Image: 68kuqWR.jpeg]](https://i.imgur.com/68kuqWR.jpeg)
![[Image: iPYHGnp.jpeg]](https://i.imgur.com/iPYHGnp.jpeg)
![[Image: bzCkhwp.jpeg]](https://i.imgur.com/bzCkhwp.jpeg)
![[Image: jlr.jpg]](https://i.ibb.co/FqqLRMk/jlr.jpg)
