Hello everyone, can you please help me identify cylinder number 5 on an Audi Q7 4M CRTC engine? I need to change the glow plug and I'm not sure which one is cylinder 5. I think it's the one on the middle, on the right bank when facing the car. Is it correct?
Also do you know if that glow plug has a pressure sensor? I know some do have that pressure sensor but does that one have it?
Hi
Please help me remove dpf . Renault Scenic II 2.0 DCI 2009 AT EDC16CP33
ADS DPF Remover didn't help, after 3000 rpm the engine emergency mode, but there are no errors
id: HW: 8200688494
SW: 1037389654
VIN nr.:
SW ver.: 8200592661
Spare:
Engine:
HW Ver.: 8200773856
SW upg.: 8200791408
DTC Df209
Df308
Df312 - I think this error is not related to DPF
All the time comes fault for fuel pressure regulation P0089-77 (by OBDII it is P0090 and U0100). Engine runs and has power, but faults present. Kindly asking to post wiring diagram for this engine or maybe some body can kick me up to right way .
i have a Cayenne 9PA with faulty abs ecu, i found one exactly the same from Tuareg, same numbers.... i put it in to car and i have two dtcs, 1486 & 1044...
any idea for how i can programming the module to car???? (if that is possible......)
Hi, please reset the counter from the 24c16 dump.
ULVWMP3 7E0035156B
VWZAZ1L2289897
I have the code but on the radio "Safe Code 2". I try 02 to 00, but didnt work.
Thanks in advance
Hello,
I bought a Fiat 500e 12.2021 with halogen headlight. I found a pair of full led headlights and I want to know that I can retrofit them.
The electric plug is the same but when I install them, they start to blink. Do you know if they need coding? What should I do to make them work?\
Thank you.
managed to f*ck up data on abs unit.
Tried originally flash it with diagzone, made error and that`s it.
So need eeprom data M95160
Software : 1K0907379CD_0120
vcp won`t give id so can`t flash sgo file wich i have.
Hello. I am trying to read the variant coding on my SAM-F module but Vediamo cannot establish communication with the ecu for some reason. When I try connecting with other diagnostic tools like Launch x431 I get inside the module very easily and can code. I want to save my current coding with vediamo before making any changes. I tried two SAMF_204 cbf's which are looking same but Vediamo is throwing different errors on them. Has anyone encountered this issues? Do I need higher security level for vediamo to go in? Thanks!
Hola chicos, ¿alguien sabe dónde está el limitador de velocidad en este flash? Tiene que estar limitado a 90 km. Solía hacer esto, pero se ha cambiado la ECU y con la nueva ECU no limita la velocidad a 90 km.
attached the damage ecu dump and used ecu dump. i need to clone damage ecu dump to the used ecu. used ecu is older than damage ecu, hopefully it doenst matter.
If cloning doesnt work, (because hw/ sw on older ecu) then it would be nice, if someone can do immo off on "new_used_ecu"- file.
hi have e90 for friend we change the headlight and we fix the 2 connection for cable where we join pin 5 and 6 in plug for high beam and add ground in pin 2.
after this I pay one person from this forum for coding he say all finished and its still not working now he say don't waste my time and he is saying my installation is faulty so he won't give refund...
is there any one who have doen this before and can help
FRM module says FRM II E90 LED NSW
S: 6135 9204532-01
AW: 9204535
I purchased some aftermarket OLED (Chinese) plug and play tail lights for my 2016 Mercedes S 550 Coupe (C217). The lights work fine, but I get errors on the dashboard indicating the Left and Right turn signals are out (they are not out). I want to code out the errors.
Hi,
I have the error B142A in an airbag module (0285013742). It's a Mercedes X-Class. Can someone help to clear it, please?
I tried a cleared fille but then I have B00A000 (Weight sensing system error) or with another file U214087 (CAN error with DME)
.
