Translator



dear all,

i need a proper vci manager for my china xentry vci

the one form vxdiag not work (interface not found)

thx in advance


br

HELLO
following a meter test the abs esp coding was lost, can someone help me find the code
ibiza 2011
1.6 tdi
esp 8.2i
6R0907379AK
VIN VSSZZZ6JZBR161368
THANK YOU FOR YOUR HELP

Hello i have damaged old ecu i buyed second and i need virgin. Can someone can help me? EDC16C36 0281017065 Thanks in advance

Attached Files

all_EEprom.rar

3

1.11 KB

Download

hello friend
i want to remove dtc in jeep 8gml ecu 
p0197 
somebody help me please
thank you

ji. I need PIN from dump Opel Insignia 2.0CDTI EDC17C59.

thx

eeins.rar

9

4.89 KB

Download

Delete

Hi guys, could someone help me start this car? I tried a solution that a friend from the forum gave me but it doesn't work. The original ECU is dead, there is no emulator for this ECU and there is no way to clone or anything I need to start it.IMMO off Peugeot 106 marelli iaw 1ap.40 - MHH AUTO - Page 1 this link in from the topic

Hello.
Mazda 6 
Software version: SH9X-188K2-E
Catalog number: SH15-18881-A
Hardware number: SH15-188K1-A
Calibration: SH9XEE000SH0B060
CVN number: F6199D44

Attached Files

SH9X-188K2-E-20241010-092844.rar

0

864.22 KB

Download

Hello,
I need to turn off DPF and EGR in Peugeot 407 2.0 HDI DCM3.4 by disconnecting the plugs from EGR, pressure sensor, additive pump
Kess reading
Regards

Attached Files

flash.rar

4

391.25 KB

Download

Hi
need ori

Manufacturer: NISSAN
ECU hardware version: 23710LE00C
Detected ECU: EDC17C45
ECU software version: 23710LE15D
Bosch software version: 10SW027684

Hi I have 2013 jcb 3dx 93c46 dash file I need calculate the hours please


Old =  166524


New=  7650

Please thanks

Sent from my SM-A235F using Tapatalk

Attached Files

ORIGINAL JCB 3DX 9346 DASH.rar

10

135 bytes

Download

Hello,

I need ori file for Audi S3 MY 2006

VIN is WAUZZ8P67A135908

THX

Hi, I need virgin in ecu as in printscreen.
ST10

Best regards

Attached Files

Thumbnail(s)
   

iaw allegro.rar

2

214.15 KB

Download

Hello

Lc120 2003 in D car starts in 3rd gear
But if i manually switch from
L 2 3 D gearbox drives perfect
Its 4 gears auto transmission
Linkage is fine neutral switch has been replaced and still no luck
No fault code except brake switch sometimes
Thank you all

Hello....

I have a problem with a passat 2007,  can't communicate with immobilizer after battery drain.....

I make immo off the ecu and start the car but I have to fix the remote locking (car is keyless and with plastic blade...)

I need the the correct  comfort module according VIN(There are a site but I don't remember  it... that provides part numbers via vin....)

WVWZZZ3CZ7P063301
WVWZZZ3CZ7P063301


thank you....
WVWZZZ3CZ7P063301

Hi,
Please send link from Aliexpress.
Best single PCB and function on BMW. Please. 
Thanks.

Hi
I need help with immo off in ecu mitsubishi colt E6T42490 read by galletto .
Thanks
Adam

Attached Files

e6t42490_boot_flash_ori.zip

3

338.53 KB

Download

Hi. I am new to this immo programming service and would like to seek your advice on how to read an eeprom file speciafically Subaru Forester Smart Key 2010 24c01 Japan. I have 2 vehicles with the same BIU and read the eeprom files successfully with Xhorse miniprog in circuit, however when opening for editing via "Write Key Via Dump Autel IM508" says file is unknown. Tried both files with Tango and same error unknown file version etc. 

Both files are attached if someone wants to have a look at them and maybe tell me what I'm doing wrong. PM if you can help, wiiling to pay

Attached Files

Subaru 24c01.zip

5

548 bytes

Download

W447 Vito 2014year

Anyone cuts rain/light sensor , have fault for communication and when start on dash goes fault for it. I want to disable this fault. I recode EZS, IC - but fault is there. On front SAM dont have this option for code on/off. Have any variant to stop dtc? 
Customer doesnt wants repair. 
Thanks

Hello,

2004 Isuzu Rodeo 3.5L 6VEI

What all do I need to perform diagnostics and programming? 


Thanks, CJ

Hi, does anyone have a tip on a Brand of high quality Aftermatket timing tool that can be purchased in the EU. Does it make sense to buy one of these at all? I have had bad experiences with most of them and unfortunately with modern engines, for example VW concern and their TSI, there is a high emphasis on precision. What experience do you have and can you contribute any advice or tips on how you deal with this?

Thanks

Hello there how are you doing? I really need help on a F22 EPS last VX33469
Its working ok, but has messages on the display "increased efforts" but its soft its not hard .

EPS info on the scanner is: Version V10.00, S63006 - EPS
Diagnosis index 0F1E80
Production date 19.08.10

It had at some previous point the belt damaged
At some point the EPS motor/module was changed
It may or may not be the original steering rack

Codes are:

482452
4823C2
4822D9

I need help dont know if it need programming module to angle sensor, module to vehicle or what
I think the rack has LB letters 

Hi everyone! Can anyone share a virgin dump for GPEC4 Jeep Wrangler 2.0 2021 (05150861AJ).

Why you choose our KTAG 7.020?

1. Our K-TAG 7.020 add a GPT cable to support GPT Functions ( GPT is new password algo cryptography that is implemented in new Tricore microcontrollers.

HI ALL, I NEED CHANGE KM EZS W906 SPRINTER 2015


KM ORIGINAL: 526806

KM NEW:147293

THANKS

hello my friend please need help
I replacment w211 2003 instrument cluster with face left instrument and virgin it to 0km and all ok but brake light in on all time so how can i coding it please help thanks alot

hello  ,  i wonder to know if i can  get rid of   Po513  invalid secret key pcm  , start and dye situation from pcm swap

pcm have been changed to a v8 pcm over the previous one v6 pcm  , doing a engine swap  i have 2 original 

programmed key that still match and respond to the oe  rf hub , i have alfa obd , and i have been able to read dump 

file from  rf hub (eeprom 95640)  and  replacement pcm (eeprom 95320)   with  

ezp2023+ , i tryed more than once to understand  all this out but i  just can not figure out witch data exactly i need to transfer to 

replacement  pcm to have it work . i need to tell that serial number from replacement pcm have been matched to vehicule , and 

unfortunately when i readed my original pcm eeprom 95640 from v6 pcm ,  eeprom was still on the board and i am not so  optimist 

to retrieve  revelant information from it  ,thanks for any help and guidance in this project 

Attached Files

gladiator immobiliser read stock1.zip

8

2.01 KB

Download

hp tuner after pcm serial number change.zip

7

1.29 KB

Download

jeep gladiator 3.6.zip

7

1.26 KB

Download

I haven't seen much discussion about the topic, is Tips an exclusively online feature now?

I had a subscription to prodiag with my old boot ThinkDiag adapter?

My subscription expired about a year ago.
Do I have to use ProDiag or do I have other options?

Hello.....

I have problem with a bmw 730d 2006.....

Engine starts but it can't rise rpm, it works to 1300 rpm and no more... 
at 1300 rpm it starts to idle.....

almost all the sensors have been changed with new genuine ones but no difference... the ecu has been changed, without any difference to....
in the live data I don't see anything strange.... the injectors have been checked....

the timing has been checked...

what else could be wrong with the car????