Hi everyone, I am using E-Sys 3.30.1 with PSdZData 4.39.20 Lite, and everything is working fine. I have full access to my car and can read data. I am trying to find the history of reset service messages, including the mileage and date when a service was reset.
My questions: 1. Where in E-Sys can I view these records? 2. Are they stored in a specific section, or do I need to access them differently?
I have this hino that the a/t light that comes on and the transmission goes into limp mode when i put hino dx2 i get this code p1604 abnormality in the exhaust brake actuation signal i cant find any info on it when i try to do the diagnostig flow i cant find the dtc and if i look at it online the p1604 code says its startability issues of the truck not starting or having a hard time to start but this truck dosent have that issue it starts fine. Has anyone ever encounter this problem im assuming its somethint to do with the exaust brake but not sure where to start.
From some time I cannot connect to my car W212 through SD C4 clone.
The error message is below.
Xentry version - 27.15.2.3
SD Toolkit - 2.1.14.2
Could someone help me to manage with this issue ?
Fault 1.?.? Initialization of diagnosis multiplexer failed. Possible causes: The link between the diagnostic multiplexer and the diagnostic socket is interrupted. The voltage supply at the diagnostic socket (circuit 30 and (or) circuit 31) is faulty.
I need to buy new Transmission Control Unit form my car. Here is the chasis number: WDB1680081J356887 I am not sure which part numbers are compatible with my transmission. Original one is A0285451332 and i cannot find the same part number. Can someone check compatible part numbers please? Thanks in advance!
Hello everyone. I am asking for help from the more experienced: on a golf 6 I mounted a cluster with MFA Plus Color 3D taken from Tiguan (5N0 920 883 G). No immo problems, everything works as it should, except the handbrake. Using VAG Dash Editor V7.3 I changed the setting from electronic handbrake (Tiguan) to mechanical handbrake (Golf 6), but the handbrake light still remains on. I know that on Tiguan the brake signal is positive, while on Golf 6 it is negative, but I don't know if it is a simple impulse or a voltage that is always present or always absent depending on whether the brake is engaged or not. Can anyone help me please? Thanks
Edit.. I'll answer myself: it is necessary to move a resistor and add another one
ELV was defective. Car do not crank. I changed with emulator. Reset ELV counter is ok, car crank but no start.
I have errors 4A62 -DDE : EWS tampering in ECU and A0AA -CAS: Control unit fault. I tryed to sync CAS with DME with Launch and with FVDI clone without succes.
Please verify my files for corruption. Car is not at me. Transmission is automatic and I suppose immo-off do not work.
I have Ista with ICOM but I'm not very skilled in BMWs. I work better with bench programmers.
Hi everyone , does somebody can please help me with a inmo off for a [font="MHH Font", Calibri, sans-serif]IAW6LPB CEM0[/font][font="MHH Font", Calibri, sans-serif]
i did it with davinci but the fault P207F still , i DTC off the P207F , after 3 weeks the car won't start because of adblue lock and no fault code in ECU
this is the original file
"My dashboard is broken. I ordered a used one online and wrote the old EEPROM to the new dashboard, but it shows miles instead of kilometers. How can I change it back to kilometers?"
org km: 293082 km (Europa)
now : 182113 miles (Currently displayed on the screen)
Hello guys , today I installed Odis S 24.3.1 to try Godiag gd 101 device , but when open the option to choоse device , there is only VAS6356 in the menu .
In the beguining of the installation I choose PassThru .
The question is how to solve the problem , and use Odis S 24.3.1 with godiag dg101 ?
i have kess v2 cloned, i cant read iaw 48p2 ecu using it, keeps saying *wake up error*
i dont know if my kess is faulty or cant read it
which tool can read this ecu?
Could somebody help me update my egs52 software? The gearbox when cold jolts at 1100-1600 rpm, I was thinking maybe a software update could help her. If any info is needed I can provide. Big thank you!
Write in the comment below on the post that you want the code and we will send it to your PM / INBOX MHH in a few days. _________________________________________________________________________________________________
WRITE IN THE COMMENT WHICH SOFTWARE YOU WANT TO USE, AND OUR TEAM WILL CONTACT YOU IN A FEW DAYS AND SEND YOU A DISCOUNT CODE THAT YOU CAN USE WHEN ORDERING ON THE MHH FORUM OR ON OUR WEBSITE
Does anybody know if you can unlock an MD1 ECU (VAG post 06/2020) with MagicMotorsport Flex, and then read and write with PCMflash (Module 92) after the unlock?
Are there any other tools than MagicMotorsport Flex that offer writing an MD1 ECU (from any VAG brand) after 06/2020?
I have this ecu 8T0907560J try read with pcmflash but epp was not read, as edc16 give me checksum error but file seems ok when try to write same problem so i try to read write with mpps after that car not start and no conect to pcmflash, i write vía bdm with ktag file from pcmflash 1 read. Now i can conect vía pcmflash again but car no start can anyne check files if seems ok? Or someone have bdm read from this ecu to do immo off i can pay for help?
Epp file was read but ktag may be is corrupt but i dont know....
![[Image: jmge1DO.png]](https://i.imgur.com/jmge1DO.png)
![[Image: YUBAto0.jpeg]](https://i.imgur.com/YUBAto0.jpeg)
![[Image: ukRlgM9.jpeg]](https://i.imgur.com/ukRlgM9.jpeg)
![[Image: u6f9VOC.jpeg]](https://i.imgur.com/u6f9VOC.jpeg)
![[Image: TxtMN84.jpeg]](https://i.imgur.com/TxtMN84.jpeg)