I will pay if someone can help with this issue ..
actually this is W212 ( CRD3.7A) the original ECU bricked after write with KESS a modified file ( make adble off of the original file +chcksum )
So i decide to but the another ECU the same number ( used one ) But now i tried to Renew with my XProg3 as this ecu is listed in the tool but without success .
here i have read by bench original (Flash + EEprom ) of The Donor ECU
FLEX interrupted file writing and blocked ECU. There is no communication in OBD mode. I read ECU in BOOT mode. I repaired the _int_flash file and wrote it to ECU but I still have no communication with ECU. I think I've put together the int_flash correctly. Could the eeprom have gotten stuck?
In the attachment ORI file read by OBD and Full backup read in BOOT mode.
Hi, I have 3 PCs w213 screen, black screen. I want to flash, but the flash can't start. I do with doip but after flash can not be completed.
A2135402740
A2135406167
(01-03-2025, 12:02 AM)mka.coding Wrote: Hi, I have 3 PCs w213 screen, black screen. I want to flash, but the flash can't start. I do with doip but after flash can not be completed.
On this file I can´t seem to find the oil pressure maps to adjust the values.
Am I blind or are there none?
Audi A6 4G 2017 with CZVA engine. My research comes to the conclusion that this is already evo2 engine with variable electronic oil pump or am I wrong?
Could you tell me how to change the mileage displaying in Ford Focus 2021. (The photo of the clocks attached.)
The value of km/miles is 1234.5km and I would like to change it to 1234km, so without the dot.
Hello .. i need info with can gateway upgrade.. now i have 4L0907468B (26pin) and want to make upgrade to 4F0907468N (20pin - have made adapter 26->20pin and route wire for load signal to pin 2). My question is do i need to remove CP only from new gateway with odis or all modules after GW upgrade will have CP - including GW??
Hi,
I have a Technisat Mib STD 2 ZR + Nav unit with SW 0241 Hw H24, the unit does not turn on. After connecting Uart it enters the boot menu unfortunately I am not able to upload the software because it throws an error (scren attached) it is possible that it is the fault of the software because I only have 0252 and 0253 I do not have the version that was in the unit at the base.
Does anyone have the VW EU software in version 0241 if so please try and see if it helps.
Or maybe the problem lies somewhere else please help.
[font="MHH Font", Calibri, sans-serif]Hi[/font] [font="MHH Font", Calibri, sans-serif]I need a pin from HYUNDAI HB20 year 2019 south america, Brazil.[/font]
Hi all. I have a problem with my GR Corolla 2023. Right after having a wheel alignment done the message about pre-collision and adaptive cruise controll malfunction showed up on the dash. There were very minor alignment changes adjustments made to the wheels. The steering wheel was not straight and they fixed that by adjusting the front tie rod and a bit of toe correction was needed on the rear. No big changes. Right when I was pulling out of the shop the car was trying to pull one way which I had to counter on the steering wheel. After a few seconds the pulling effect stoped and the car would drive straight with the steering wheel straight but the malfunction warning showed up on the dash. I have Techstream and there are no DTC codes in the Radar ECU and no DTC codes for the recognition camer. The steering wheel deg sensor is showing 0 deg when the steering wheel is straight in the middle. I was able to do the online (driving) radar and camera calibration with success but that didn't remove the malfunctione error. Like I said no DTC's at all. Not only connected to the radar and camera but no dtc's at all. Working with Techstream 18.00.008. Any ideas?
Hi to all Members !
Have an Lynk&Co 01 Hybrid after Crash with SRS ECU:
8888855312B
512013
Bosch: 0285013153
MCU : R7F701330
Can someone please help and clear : crash and error U3000 .
And the car dont start, can it be beacause of that error's in SRS Ecu ?
Thanks to all in Advance !
I have some mappacks for various BMW engines and transmissions in XDF format, unfortunately I don't have the XDF KP plugin in WINOLS and now I need your help.
the person who helps me to convert the XDF to KP logically gets full access to the whole mappacks so win win situation. these mappacks are not public!
HELLO, I AM 19 YEARS OLD, TURKISH, NEW TO THE FORUM. I WRITE IN ENGLISH BUT I WRITE IN TURKISH WITHOUT KNOWING I'M SORRY. I HAVE A C5 DEVICE BUT I HAVE NO PROGRAMS. IF ANYONE CAN HELP I WOULD BE GRATEFUL.
Hello, I have the car with water demaged airbag module. I have took secondhand one but with crash. I have made a crash clear by AIRBAG_Toll software but with this file there is chksum errors and other errors.
Hi,
I reacently retrofited and coded NTG 5.5 on Mercedes W205 facelift. Everything works well except rear view camera.
Problem: screen shows all object in wrong side ( objects are on right, screen shows on left). I tried calibrate camera, tried another camera with newer software date, but nothing helped. Coding seems right.
Hi I have changed the screen and have the same issue. Have also reworked the cluster. i cannot find an alternative cluster with the same part number VPGRRF-10849-DE. What would be a way forward i cannot purchase the same unit. Can find similar with same design but slightly different part numbers.
Any help be much appreciated have included pictures also.
![[Image: Bild-2025-01-02-170326973.png]](https://i.ibb.co/XpKgW0t/Bild-2025-01-02-170326973.png)