Hello everyone.
I'm thinking updating or flashing some modules from my car S205 from 2018 using dts monaco.
When I use software finder to find the most recent updates, some of the smr-f and cff files have not any bin files.
Should I always have a bin file when flashing?
Where can I find the right bin file for every module?
MB W177 c180D 2019 after overfilling the Adblue, the sensor to measure the level never worked again. In consequence cannot read the level and the engine light is on in yellow around 4'000 km have been driven.
Replacing the AdBlue tank is out of question as it's +2k.
What would you recommend? Delete AdBlue completely, suppress error? I only have DTS Monaco, so if there is a workaround with DTS, it would be great, otherwise it will cost me more.
I read somewhere that someone managed to disable AdBlue just with DTS Monaco.
Error codes:
U05A308
U05A387
Hey guys, can anyone send me the correct updated cff files for these 2 door control modules? The temp monitor is bad on both locking them and I need to update. Using Vediamo.
Vin: WDDNG71X07A119909
2007 Mercedes S550
Front Right Door Control Module:
MB number 2218701087
software number 2214421832
Rear Right Door Control Module
MB number 2218704287
(autel device does not display a software number for either rear dcm's)
Hello friends can someone help me by deactivating the immo of a Nissan versa 2007 Hitachi MEC90 372 my whatsapp is +50684633463 someone help pls and thanks
hello i read eprom 35160 by r270 from cluster mini f057 , i need virgin this , , i found vin by hex edytor but only long vin, eny help with this ? ps millage stay
rep and thx if helped [font="Fira Sans Condensed", Calibri, sans-serif][b][b][b]Ukairbags[/b][/b][/font][/b][font="Fira Sans Condensed", Calibri, sans-serif] [/font]
A good friend of Mine owns a Audi A6 2.7 TDI with and EDC16CP ECU and he got a Letter from the German Kraftfahrtbundesamt because of Emmission recall.
He dont want to Update His Car, but unfortunately He has to at an Audi dealership.
I dont know exactly what is going to be flashed on this ecu, but would it be possible to read it via BDM and after the appointment at the dealership Just recover it with the old Data ?
I am working on a Kenworth t800 with a PACCAR MX 11 EPA10.
It is deleted. Customer said he has owned it for a few years. It was deleted when he purchased it. It has recently started where is has low power. I connected to it with Davie software, there are no active codes and also no inactive codes. I am limited to performing testing with the EPA 10 with the Davie software. Here are the tests that I've ran. Turbo actuator test, BPV test and also a compression test. No problems found
I took the truck on a test drive. It seems to surge and struggles to pick up power. The engine has new fuel filters and a new air filter. I ran an overhead on it as well. No luck
I will pay if someone can help with this issue ..
actually this is W212 ( CRD3.7A) the original ECU bricked after write with KESS a modified file ( make adble off of the original file +chcksum )
So i decide to but the another ECU the same number ( used one ) But now i tried to Renew with my XProg3 as this ecu is listed in the tool but without success .
here i have read by bench original (Flash + EEprom ) of The Donor ECU
FLEX interrupted file writing and blocked ECU. There is no communication in OBD mode. I read ECU in BOOT mode. I repaired the _int_flash file and wrote it to ECU but I still have no communication with ECU. I think I've put together the int_flash correctly. Could the eeprom have gotten stuck?
In the attachment ORI file read by OBD and Full backup read in BOOT mode.
Hi, I have 3 PCs w213 screen, black screen. I want to flash, but the flash can't start. I do with doip but after flash can not be completed.
A2135402740
A2135406167
(01-03-2025, 12:02 AM)mka.coding Wrote: Hi, I have 3 PCs w213 screen, black screen. I want to flash, but the flash can't start. I do with doip but after flash can not be completed.
On this file I can´t seem to find the oil pressure maps to adjust the values.
Am I blind or are there none?
Audi A6 4G 2017 with CZVA engine. My research comes to the conclusion that this is already evo2 engine with variable electronic oil pump or am I wrong?
