Please can anyone help on this Issue...
I have here C3 from 2002 1.1 Marelli ECU
Problem with this car is SRS dash lihgt allways on
DTC in SRS unit is = Van comunication not defined
DTC in BSI = Comunication fault on DATAB wire with engine relay unit
Hi, I need help to change the VD 46 ECU configuration, the engine has been replaced and now we have a new color of the oil dipstick, unfortunately with the original software there is no possibility nor with other tools, I would be grateful to anyone who could help me
i have Mitsubishi Galant 2009 chip is Hmh8304f , i made off by other program but it give me same code for immobilizer can time out
this is the two files the original and the new one off by CarEdit v1.28
Can someone DPF off my original file? Is a 2007 VW Passat 2.0 BMR engine Siemens PPD.
The consumption increased and it goes into regeneration mode every 15km..
There is no black smoke or known problems with the engine. The car works perfectly.
Please someone with WinOLS Experience.
Davinci doesn't correctly modify that file.
I've used 2 spared files, but both are lighting the DPF on the dash and no fault code is saved on the ECU.
The DPF filter is also untouched. All sensors are connected.
Also after writing the MOD file do I have to disconnect the DPF sensors and EGR?
Need to swap bcm but the old one burned, read the eeprom so far but dont have an adapter for a qfp176 to fully clone.... Have vvdi prog, keytool plus, j2534 jvci autel, and prodiag....
please can someone help need this van working tomorrow...
Hello im getting this after read eeprom with an eeprom reader (only read, not write), no communication from obd port (clip or DDT) Rlink 1 Any ideas how to solve it?
Hello. I have 2006 Infiniti M35x AWD JNKAY01F16M260830 DATE 11/05
I can't find correct part number for TCM programming. Now TCU p.n is 31020-7s505 . I think this wrong part number for this car.
Maybe some body can give me correct number, or flash file. Thanks.
Abrites comes with everything in picture
I purchased Subaru reset , Tesla ,motorcycle bike licenses
my active subscription with hardware protection ends this december 14th
Attachments are Tesla adapter hardness ZN072
AVDI CB203
Harley motor cycle adapter
Subaru All key lost emulator and Tags
ESL emulator EM001
2 Tesla Key cards
Hardcase
Shipping from Canada
can provide more information if requested
Hi this is the first time i came across with this dtc, does anyone know how to fix it?
No crank no start, all modules passed but pcm has p062f, p161a, p161b
Hi all member please help I have big problems with Land Rover hybrid 2016 with P0B3C-04 P0B3C-62 P0B3C-92. P0B3C-96 and P0A1F-49 this car not show real cell have problems all have experience help me
Fitting an aftermarket head unit and steering wheel control interface (BOSE MOST system) on a 2005 SL. I can't get the steering wheel interface to work and have been told that I need to change/code some settings in Xentry to get it to recognise the canbus steering wheel control interface...does anyone have any ideas?
I'dd like to read and flash my 2019 euro civic FK6 1.0 vtec turbo PCM 37820-5az-g24 (MED17.9.3).
According to https://www.alientech-tools.com/news/lat...uite-3-92/ MED17.9.3 is supported as of version 3.92, so i guess a chinese clone is out of the question, as those only go up to version 2.80, right?
Hi, I have a clone Actia J2534 Pass-thru adapter (First gen blue and yellow) It works most of the time but not all that stable, I also have genuine tool, but the serial won't work with the clone software, Is there any reason I can't remove the memory chip from the clone device and swap into the Genuine to be able to use the genuine tool with multidiag?
I have to read an eeprom from a Delphi 3.4 control unit. I have already tested several schemes and none of them read it. I have the VVDI prog programmer.
Hi guys, I see a few here have been looking for this file, as it is not able to be read with a tuning suite, only remove flash chip and use chip reader, am posting here free for all. Thanks and Rep if it helps
