I have an Opel Mervia B diesel with Delco E98 ECU.
Customer complaint, that after roughly 50 starts, the car do not start and he have to make car powerless and then the car starts again and the loop closes.
Fault code stored is B1527 "Parasitäre Last".
I have heard, that this cars had problems with a faulty BCM module. So the cheapest thought is to deactivate immo.
Do someone have experience with that and can help me?
Anyone had any issues with this SPNMVL module? It had lost connection and now the drivers seat massage doesnt work at all. Everything else works. There is no error code in the ista about connection problems, just the module shows up red.
Every now and then I need wiring diagrams for different makes of car but find it difficult to find any.
Anyone know which software on mhh are good for wiring diagrams?
Ps:just now I need Vauxhall Astra G cdti 1.7 Z17DTL 2005
hi guys , so long story short , mini r56 in with SZL swap to abilitate cruise and radio volume buttons.
swapped in szl with latest part nr (checked on realoem) buttons work but can't set steering angle. tried with inpa , it gives error on -15 +15 steering angle condition , tried ista d , failed , inpa shows all the degrees when moving the szl ,
as last chance tried tool32 , szl56.prg and using comands steuern_lws_ableichen , no luck gives argument error : tried no argument , 0 , 1 ,0x00 , start
flashed DSC and SZL just to be sure with correct vin , coded both oe with ncs :nada
now the fun began : put back old szl, even worse , inpa can't even see steering angle on this one now.
is there any of you that have done szl angle calibration and can point me out what other things to try
Hello, I need to turn off the immo in Renault Kango .edc15c3 0281010894. Do I need an emulator and desolder the Eprom from the controller? ..I have a kt200II and it can read the eprom on the table..Is it better to use an external programmer?
Hi all!
Installed an original kit with a rear camera,coded
When turning on the reverse gear, the camera and parking sensors do not show, the message "system is not working" appears after that, the error b1e7b00 appears in MBUX image from the rear view camera or the park pilot is missing or broken
The cable from parkman to mbux was changed, when we disconnect it, the error changes to a constant one due to a break in this wire
I have a question, could the encodings be incorrect? Can someone tell me about the encodings, suddenly there was a mistake there
Sorry for my English, it's not my native language
Hello
i have a Auris that came from another office that not start.
I have trayed to make OBD sync but not work, may have cables broken
between ECU immo box !
On this car are critical to remove immo box.
Are possibile to make immo off on this ECU EDC17CP07 auris 1.4 D4d ?
Diagnosis identifier 00510B Control unit variant IC213_IC205_213_222_E035 Manufacturer-specific serial number 0033664215 MB object number for hardware and software 2059004842
Hello, i have a error for heating rear O2, but car is Cat - free. Can i disable second O2 sensor with Vediamo or Monaco or need Ecu flashing. In this line of thought, is it better to remove the rear sensors or replace them with new ones?
I have changed the display in my V class from small to large.
The image is still displayed as on a small display.
I have not found any coding to change the resolution in the radio
Maybe the change should be included in another system?
Is there any solution to this problem or do I have to replace the radio?
I can buy the radio that came with the display, but what about the protection of the component, how to deal with it and is it only a matter of the radio?
Im waiting on my Fg tech / Galletto to turn up so i can bench flash my file . Whats the correct procedure to bench flash when does the ground wire get added then removed
Hi , i broke isuzu dmax 4jj1 ecu , i have original partial maps file but im searching for full dump to restore with ktag , ecu software is 98170820
Ecu is transtron tti 0100 , can anyone help me please?
hi guys
We have Jaguar XF BCM that is corrupt after flat battery, can someone help with recovering the EEPROM from D-Flash, we have read it using VVDI prog,
Original Vol-vo VOCOM 2 Tech Tool 88894200 Truck Diagnostic Tool Full package with Lenovo T450 I5 8G 256 SSD Software Ready to use.
Original Volvo VOCOM 2 Tech Tool 88894200 Description:
This VOCOMII is dealer shop tool which produced in Germany. It covers all the functions of the VOCOM2 VOCOMII 88890400, which doesn’t need any cables accessories and can be connect to the laptop via WIFI perfectly.
Tech Tool (TT) is a tool that supports the repair and diagnostic process. It was developed to make repair shop tasks easier and more efficient. TT can be used in the repair shop, out in the field, at the roadside, or during test drives. TT is a diagnostics application that covers the whole repair process through the use of plug-ins. With TT you can diagnose, test, calibrate, and program a product. A product could be a vehicle, engine, or a machine. TT also provide functions for updating the tool, communication with the product, and other external applications. The set of plug-ins, user authorizations, and available languages is adjustable to provide every user with what they need.
Vol-vo Vocom II Genuine Adapter Features:
1. Original VOCOM II Mini 88894200 WiFi Volvo truck diagnostic tool, made in German
2. Support OBD2, 9-Pin, 6-Pin, FCI, MEFI, BNA, OBD2, 9-Pin, work on Vol-vo/Renault UD/Mack trucks from year 2002
3. Vehicle communication protocols: ISO 11898, ISO 15765-2, SAE J1939, SAE J1708
4. Support Vol-vo/Renault UD/Mack trucks made since year 2002
5. Connect laptop by WiFi , no need cables
Support Truck Model:
For Vol-vo Trucks - Older electrical system, Vehicle electrical system '98; VERSION2, VERSION3; VERSION4 - FH4/FM4
For Vol-vo Buses - Conventional, Multiplexed, Multiplexed v2, Multiplexed v3
For Vol-vo Construction Equipment
For Vol-vo Penta, Marine engines - VERSION2, VERSION3
For Vol-vo OEM Component Customer - VERSION2, VERSION3
For Mack Trucks - V-MAC I/II/III, ITC, IV, IV+
For Renault Trucks - VERSION2, VERSION3, VERSION4; (EURO 6, DXI, DTI)
For UD Trucks - VERSION2, VERSION3
VOCOM 2 Tech Tool 88894200 Interface Function:
Identify a product.
View information history.
Diagnose a selected product.
Test a selected product.
Program a selected product.
Calibrate a selected product.
$1458 To Get One Vol-vo VOCOM 2 Tech Tool 88894200 with PTT 2.7.116 Software Installed in laptop>>>
For more details, feel free to leave your comments or send us a message.
![[Image: Original_Volvo_VOCOM_2_Tech_Tool_8889420...1733387336]](https://cdn.shopify.com/s/files/1/0072/5424/5449/files/Original_Volvo_VOCOM_2_Tech_Tool_88894200.jpg?v=1733387336)