Hello. I recently swapped my W204 pre-facelift steering wheel with one from W212. The steering wheel is the version that is also used in W204 facelift, but I couldn't find one from W204 at good price so I bought from W212. The steering wheel is plug and play with no issues and all buttons are working + shift paddles. I didn't swap Steering Column Module, only the steering wheel. Now I have 4 faults on SCCM which are the following:
B1EB000 - Lane Keeping Assist has a malfunction.
U11A300 - Communication with control unit "Multifunction camera" has a malfunction.
U119800 - Communication with intelligent servo module (ISM) has a malfunction.
P172A00 - The Direct Select lever has a malfunction.
None of those features are available on my car.
I understand that the steering wheel is from E-class and it tries to find its features like Direct Select Lever.
I have no issues everything is working and it is not bothering me... I just want to ask if it is possible to tell the steering wheel that it is operating with W204 and not W212. There is no variant coding for SCCM. I looked at the diagrams of SCCM and Steering Wheel and I found that no matter if the vehicle is C class or E class or whatever, all of them have pins for Direct Select lever but somehow on C class is disabled. Is there a way to clear those faults and tell the steering wheel what is the car? Are softwares different for different models and if so, what number is for C class which has ESM and not Direct Select + ISM.
ho letto l'id ecu con kess3 ma quando provo a leggere obd si è fermato con la chiave di errore N e l'auto non si riavvia mai non è possibile diag su obd e hanno un altro errore ecu CAN comunicazione ecm
Provo con l'avvio ma non è possibile leggere la password con kess3 e dfox
È possibile che l'ID in avvio invii solo 15volt e 6/7 ampere, ma non è possibile estrarre la password ECU
Compro ECU usato, ma non è possibile clonare perché non hanno ECU di backup Ori e Immo fuori da questa macchina non è possibile
Qualcuno ha una soluzione o informazioni per risolvere questo problema????
Hello I have a w213 with a M256 engine have been working on.it has an error code P0087 fuel pressure low and have changed the fuel pump,high pressure pump and the fuel rail sensor but I still get the same error.ones I eased the code the car driver and goes into limp mode again.pls I really need help here.
Hi everyone, after several tests, files and so on, and knowing that these engines are what they are, I still don't notice a big change in power in my 207 HDI, this is the last file purchased and the difference is minimal, what do you think? Where is the safe limit of these stock engines? Attached maps
I want to add a new key to the Audi Q5.
I used odis online to want a new key but the procedure fails because it does not see the key. You have to put the key on the antenna (cup holder in the center console) only then the key coding continues. But with us a key is never detected on the antenna.
What other tool can I use to learn the key on this Audi Q5?
hey can someone maybe take a look at the pop and bang. the problem is that it doesn't pop properly and only for a very short time
hey, maybe someone can take a look at the pop and bang. the problem is that it doesn't bang properly and only very briefly. it's supposed to bang really loudly and continuously
Hi.I have 1 working key with keyless.And i have china made MQB key.I want this key match with x-prog3 via Launch.But afraid.Or here is people wich was do it work?Or with x-prog it safe?Or Launch real can calculate MQB chip?
This time Ioniq 2019. Car is from USA, the owner wants to change the region of the instrument cluster to have Celsius, kilometer mileage, l/100km measurements.
I've ridden somewhere that it is possible via EEPROM. Anyone of you tried this? Any advise?
Hello.
i need cloning this ecu 045906013D(0281013012)orig from car to 045906013E(0281013010) donor ecu,>>>>>>> or make immo off for 045906013E(0281013010).
Thx
Hello do someone knows wich wires are brake pad wear wires on abs unit?I bridged them on brake pad sensor but brake pad light still on.Check brake linings on instrument cluster.And other problem if i accelerate then says 4x4 inactive and trifecta lights on.After restarting car all is ok until i accelerate.While driving normal all is ok.Anyone has same problem and mabye can help?
W1N4652101X005052
New G classe
Hi to all members!
After diassemble/ assemle left floor cover and central console i have issue in ESP module C006A04 , about integral error of rotation sensor. I haven't newest xentry here, just x431. This error was before i do unlock function in SRS.
Also was many errors in srs unit about driver seat sqibs, ESP and WSS comunication. So SRS locked with integral error, but after unlock function, driver seat errors gone. Now I can't lock SRS with x431. But now it's not bother me so much, like rotation sensor.
My first qwestion is were rotation senor is located? Is it integrated in SRS ECU, or separately? If You have location, or wiring diagram- help me please!
Hi, Guys
this is Discovery 3 SID204 Flash Data I Extracted From Used ECU From Xprog Clone.
I hope This Will Help For Somebody In This Group.
Thank You
No Pass Enjoy
