hi does anyone have any damos because i need to undestand something with these ecu on "newer" engines, i send them to reball mpc and always comes back that don't read map sensor or it is not linearized (because if you start the car and accelerate it reads and if it stay in minimum map goes to 800mbar) i don't understand what happen everytime same problem and i end with other used ecu ahahha really no sense...
Hello
I have a project to modify audi tt mk1 APX 225hp engine.
I just rebuilt the engine with the following preparation:Turbo k04 stage2 (up to 310hp)
Donwpipe decata
Reinforced connecting rods
Reinforced clutch
Fuel pump sytec265l/h
630cc Injectors
Front intercooler
I would like to find someone who has files already modified for this configuration for me to drive on the circuit with more hp and torque and if possible ethanol.
I read the file with galetto but the car was already reprog stage 2 and the file seems to protect.
Does anyone have a solution to help me?
I am looking for a solution to convert cars from the US to the EU. I would be happy to buy it, If you have a solution, write to me.
All BMW
All Mercedes
Mazda - MZD2
Volvo - Sensus
Ford - Sync 4
Maserati 2013-2015 /2016-2020
Mitsubishi / Nissan
Kia / Hyundai
Chevrolet
Jaguar / Land Rover / Range Rover
Porsche PCM 3.1
Hello from Greece.
Please if someone can compare the file to i download from the Opel Astra J to i buy a month ago, with the stock ori file from denso sh7059 ecu. I know that my file it have DPF/EGR off but because of abnormal high fuel consumption, i thing it have also a tuned fuel and perhaps it is bad tuning. I do not have the ori file from this ecu and i cant have a way to compare my file with the ori one, so if some one can do it for me, it will be very helpful .
Thanks in advance
Dimitris
Hi guys i need swap CEM in XC90 2004year i have this CEM:
CEM H
30728357
04W373
12217779
can me somebody tell which other numbers of CEM i can use for replacement??? this one is problem buy , only few on market and other side of earth shipping is long and rich.
i changed the turbo actuator of a 2008 Audi A8 4E 3.0 TDI, because of an electrical defect.
New actuator (repair kit from Borg Warner) seems to have same fault code, but i think it just needs programming/calibratiing. I read, that audi dealer has some special device to do this (VAS xxxx), can this be done by other device too? Or even possible without special tool?
I just worked on my first tuning project and created a file for a VW Passat B8 2.0 TDI 190PS (2018, EDC17CP74).
There’s a good chance I’ve made some mistakes, so please don’t be too harsh.
Hi, I opened eps from vag and I saw some strange changes on(I suppose) transistors structures, can you tell me is it structure damage leading to short/open circuit?
Hello, please count the checksums for my new stage 1 file, I made such a controller a few days ago and my DC706 coped with the checksum and now it doesn't want to do it, I'm uploading the original file and stage 1.
[color=var(--COEmY)][img=16x16]data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAABQAAAAUCAQAAAAngNWGAAAA/0lEQVR4AYXNMSiEcRyA4cfmGHQbCZIipkuxnJgMStlMNmeyD2dwmc8+sZgxYJd9ErIZFHUyYYD7fkr6l4/rnvmtl7+KitrqV/fq2Y5eLY3Z9S48eRLe7BmVZ9qhTLhQ0algzZWQOVKSsCF8OjAnwbxDTWFDUhPK/jMr1H6HE/IqRky2DyvCefuwItwZzodVoYRiLqMkVCXrwpJ9twZ+sgfDYEFYl8wIWxZ9uFf7zkallxlJh4YrLGsKjZRx7VGHhLqwgFUN45DGdb8MeXGpgB4ABZdeDcpZEY51A+hyLKz4S1W4MQWm3AibWtgWmk6dyISa1pSdyWTOlLXVp0+eL9D/ZPfBTNanAAAAAElFTkSuQmCC[/img]
Hello! I have a problem. Can someone help me with this pops&bangs? They are only working in Park or Neutral as car is automatic gearbox. In Drive are not working. 2.0tfsi 180hp med17.1 ecu. Thank you
Hi all
Hope someone might help me out with this one.
I have damaged engine ecu out from 2017 qashqai 1.2petrol,owner got 2nd hand ecu same numbers.
I want to clone the old ecu,and I can't do it with trasdata(slave).
I have openport 2.0,pcmflash with module 53 and 59 ,also powerbox and combibox for pcmflash.
Pinout for power box will be this same as for trasdata,boot/,cnf, power etc.?also witch module and box will be the best for this job?
Thank you
Hi. Hi ford focus 2017 has misfire on 2 and 3 cylinders. I need original flash or calibration file. I post my full read by fgtech galletto. F1FA-12A650-FTA AV61-12B684-DA 10174794AA
I bought a 2007 zafira B 1.9CDTI 8 valve with new clutch and slave cylinder. I can barely shift gears and i can deel the clutch pedal only slightly disengaging the engine
First i tried just bleeding the clutch
then i changed the master cylinder and bled
I checked for loose bolts around the gearbox
There is no leak from fluid lines to slave cylinder
I took out the gearbox, part nrs are:
Pressure plate: 124 035 110 flywheel: 415 0241 10 Slave cylinder/release bearing: 510 0180 10 Luk Disc: 324 0394 10
Hi
I'm trying to update the gearbox software in a smart 451, I have the correct flash file but need the correct cbf file to do it with vediamo. Can someone please share?
I have searched xentry folders and vediamo but can't seem to find them
Firstly a shout out to two members who have supplied the software to get me to this stage: @manachkin / @sam!K / @mhh0010 - thank you!
Also to those that contribute to fixes and solutions.
I have the following / performed the following steps:
Clean install of windows 10 Enterprise
Install of XDOS 2024 09 from manchkin
Install of fullfix by sam!K
startkey successfully added in ConfigAssist
install of SD Connect Fix for versions 03 2024 up by mmh0010
Changed language of toolkit to English
Configured Laptop lan IP to 172.29.127.119 - subnet 255.255.255.0
Performed Software Update of C4 in SDConnect (3 updates)
Modified DAS\BIN\cal.ini & Xentry\bin\Caesar64\asam3d.ini to paltform=part_t & drivers=T (checked these are unchanged after opening of Xentry)
When trying to connect to car and run diagnosis I get 'Initialization of the multiplexer has failed'
I noticed the SDConnect padlock doesn't close
If I open Config assist I get the option for VCI or VCI with simulation. Maybe I did something wrong here?
I have searched for many solutions on the forum and think I might have missed a step or done something wrong!
So please if you have any suggestion or even to call me stupid - that is fine
)
