is there someone that have working soloution for citroen Jumpy 2019 DCM6.2A Adblue off without message in dash? car says no start after 2400 km. I already did al resets and flashd with new file but its still the same even with adblue tank unplugged. if someone have working soloution i wil be glad to hear.
So I have an old 4d56 pre 2008 shogun sport 2.5td
Its had more attempted remaps than Toyota does recalls. I know the e6txxx is not a commonly tuned ecu, though ecm titanium does have a driver for it. I've had free and paid maps that either didn't make a difference, or just rolled coal with no signifant gains. It's a well kept engine and performs like a stock 2.5td should.
Has anyone actually mapped one with success?
Have attached the ori as someone must be able to give this a simple slap..
is there a free solution for berlingo ecu md1cs003 without the need of 3rd party ?
please let me know, i only work on this model in my shop. i have a shop only for toyota vehicles but toyota and PSA group made the mistake of
giving birth to the TOYOTA proace. which is a berlingo in disguise. is there a tool that can do DPF OFF SCR OFF DTC OFF and more for this model only ?
Hey all,
I'm in need of a BMW programmer for exchanging a used gearbox on an E60. I'm between the FC200 and VVDI BMW at this point. Both are close enough in price that I'm not overly concerned about that, I'm more interested in which of these may be more useful overall moving forward. I almost exclusively repair german vehicles, and I'm sort of leaning towards the VVDI BMW or VVDI BIMTool Pro for their ability to generate keys. Any insight one either interface would be helpful, thanks in advance!
Smart 453 I tried to do Teach-in of clutch engagement points with xentry after replaced (Clutch actuator ) but failed Car start but not moving on P or R any suggestions ?
Error code : P195592 The maximum position of the component M14 (Clutch actuator 1)' is implausible. The function or the instruction is faulty.
Result of teach-in process Teach-in of the clutch engagement points was not successful. Teach-in process of component 'Clutch 1' The teach-in process was not completed successfully. NOT OK Associated learned values: Name Clutch 1 - Clutch grip point Clutch 2 - Clutch grip point Teach-in process of component 'Clutch 2' The teach-in process was not completed successfully. NOT OK Actual value 3.00mm 3.00mm Specified value ≥ 3.50 ≥ 3.50 Result of test and further procedure Clutch grip point
The values of component 'Clutch 1' are faulty. / Clutch grip point
The values of component 'Clutch 2' are faulty. / Clutch grip point
Read out fault memory and process any displayed fault codes according to the specifications
Further remedies: Teach-in process Repeat teach-in process. Check of preconditions Read out fault memory of control unit 'N15/13 (Double clutch transmission control unit)' and process fault codes. Repeat teach-in process. Check of preconditions If the process cannot be completed successfully even after multiple repeats, contact the relevant product
Hi i wanna buy a new diagnostics device, can me please give me a recomendation, which device is better MB VXDIAG VCI or C6 VCI clone for Diagnosis wia XDOS Xentry and Programming,Coding wia Monaco on new cars like W206,W223,W297... and from were to buy a good high Quality device? thanks for help in advance
Hi
I have a problem
Seat leon 1.4 tsi
med 17.5.21
Someone was doing something in the file and I don't know if I have start stop disabled.
Problem with starting.
I will try
Please disable start stop
i try noread off
maybe write odis ori first?
Anyone suggesting something?
Odis id ist 04e906016f
needn sgo file
Thx
I have this problem after flashing stage 1 on Mercedes E class 2017 MD1CP001: P60764 error and inconsistent acceleration for just one second on full load after that the car drives very fine with stage 1 until I start the car again and it does that for just 1 second.
Ori+ mod file attached. Torque monitoring is off, I tried inhibiting the DTC on another file but issue still pressent.
Hello, I jumped started my car, after first jump start it worked, second day, my brother did a jump start. No sure if he used wrong terminals. car will no longer start ( engine start).
tried a lot of things, bought new battery, it doesn't even attempt to crank / or start. checked all the fuses in engine bay and BSI, now car is no longer recognizing the key ( it used to but only when pressed against steering column.)
A lot of BSI errors and failed ecu communication when using diagbox.
Can anyone assist in starting the car? ready to pay for remote assistance. Diagbox report attached ( at the time the car could recognize the key but not start.)
hi does anyone have any damos because i need to undestand something with these ecu on "newer" engines, i send them to reball mpc and always comes back that don't read map sensor or it is not linearized (because if you start the car and accelerate it reads and if it stay in minimum map goes to 800mbar) i don't understand what happen everytime same problem and i end with other used ecu ahahha really no sense...
