After try to update software of engine ecu, it only answer to diag, but does not function, other ecus does not see it, it not showing any dtcs and actual values.. Only idents.
Car is Audi Q5 2.0 tfsi hybrid 155kW, 2012
Program Consistency: No Program Present Bootloader Programming Status - False Result Data Record - Programming Status - False Result
Any thoughts ? Is orig flash helps ? OTP must be same in same sw versions.. so must be no problem with full rewriting in boot.
Or problem can be somewhere in corrupted eeprom also..
hello, i have problem with my mazda 3 1.5 engine
Always smoke from exhaust when drive and accelerate
Dpf cleaned but after ~600km have dpf error
EGR-B have also error when drive but after some kilometers - cleaned filter between dpf and egr-b but now clogged again than means i have a lot of black smoke after dpf filter
Turbo replaced
Injectors tested - they are ok
Car have normal power, drive fine (except smoke) until get egr error
Any tips?
i have file from ecu, maybe there's a problem - i dont know is that original or not... maybe someone here have original file to compare
Is anyone able to help regarding a W164 EIS problem. the EIS part number is A1649051600
This has the NEC amazonas chip which cannot be cloned
I have tried cloning it to a matching part number and it can be erased but not be rewritten. I have the full data from the original EIS including key password and ID etc
Does anbody know which type EIS it can be written to, I believe there is a difference between dealer EIS and non dealer?
Can anyone please advise on the best way to fix this.
Hi everyone, I'm looking for an Ori Flash + EEprom Backup of an Engine ECU for Land Rover Evoquè with Bosch MEDC 17.9 Engine ECU with Automatic Gearbox. The engine control unit data are: HX73-12C520-FFE 2.0L BOSCH 0281034814
SOFTWARE UPGRADE FOR EXAMPLE: 10SW035135 OR OTHERS SUFFICIENTLY AS THEY COME FROM CARS WITH AUTOMATIC TRANSMISSION.
hi guys I have to do dtc off p0420 on a 2015 ford fiesta 1.0 kat. Ecu Bosch motronic Med 17.0.1, I have ktag clone v7.020, is it possible to read and write with this? In your experience, will I have problems?
This dashboard is with hc912dg128 mcu is it enough to just transfer mcu eeprom from original to donor? Flash files are not same but on this mcu i cannot erase or write flash. Vvdi prog and orange5 failed to write flash
Hi to all, I have a MODUS 1.2 with immo problem. Car won't start. I'm looking for immo off solutions.
Do I have to disconnect anything from the ECU? I don't have the car with me, just the ECU.
ECU DATA
SIEMENS SIM32
S120200102 B
8200414422
8200401568
Hi i looking for ori dump files for for Med17.2 g 0261s10197 someone make big fail for this files car lots a over fuel . soem one try do remaps and make big mistakes and his dont have any ori files from this car.
Thankyou for any helps.
I'm looking for advice what should I buy. At the moment I have expired diagzone with thinkdiag2 and I'm not happy with it because it often didn't worked as described for example it has problems with setting new battery in old bmw e90.
At the moment, soon will be BF and I've noticed Launch X431 Elite should costs about 300$. I have no experience with launch devices and I don't know if this cheap version is good compared to my current setup..
What would you choose - mentioned Launch or current thinkdiag2 with different program, for example ads or x-pro5 (after flashing thinkdiag).
I need to clone or immo off on a 2006 Vantage Vistron ecu to a replacement used ecu
Vistron
I've read the ecu with my Kess 3 but it dose not read the eeprom
It seems I have read the eeprom direct on the board or remove to read.
Is there a tool that will read the eeprom via boot mode with out removal of the chip ?
Can we immo off these ? eeprom looks to be 950403 st 9644W
Quote:Installation in Multiple PCS with KG: Send PM
File size: 30 Mb Update: 2022-12 Region: All regions Type: Diagnostic Software for Kohler Engines Interface Language: English Database Language: English OS: Windows 11, Win 10 Number of Discs: 1 Version: 2.11.0013 Adapters: Kohler EFI Engines Diagnostic Kit High speed download link Instant download after payment, no waiting
Kohler EFI, includes diagnostic functions for all KOHLER EFI engines with a 4-PIN diagnostic connector, including: CV & CH EFI series engines, LH EFI engines, EC series engines.
This release of the software adds support for the new ECV/ECH series engines that utilize the new DELPHI engine controller.
This update to the diagnostic software includes new engine selections and revised trouble code descriptions & diagnostics for oxygen sensors.
can someone do immo off for this ?? edc17c74
did akl but ecu not accept for some reason... or maybe someone can calculate cs? maybe it was wrong dont know.
