[color=var(--YLNNHc)]Hello, I need the original engine control unit software for the BMW F31 318d, automatic, built in 2013, which I can flash with KTAG, I want to have the original condition again! I would be happy to hear from you. Thanks[/color]
Hello
Can somebody with access to erWin download and share the latest SSP files in English or German?
The latest shared SSP files describe VAG cars from 2018. Nothing newer than that.
Regards
I am struggling to find how can I actuate(test) the auxiliary battery charging relay using Xentry. Is it in the Rear SAM module? Maybe another module?
Which relay should I actuate to test it?
Does anyone know if there is any downloads of a software that I can put in a customer name and reg of the vehicle and create maintenance records, just to make it easier to check back on to see what was done and when it was done.
Hello I need for my ford transit tear tag or calibration number to reprogram ECU. Vin WF0NXXTTFNCL34006 local dealer was unable to provide it to me due to unknown reasons... Thank you
Does anyone have a password generator for W212 N69/1?
I need to do adaptation of window raising and it requires a special function password. I can't find un in any publicly available pw generators.
VIN: WDDHF5GB4AA229000
I also have gds2 installed and working fine with vxdiag legit with J2534 passthru license
can someone help me with programming my vehicle with teamviewer?
the car had water damage and almost all modules are replaced.
The problems at the moment are:
* front turning lights (blinkers) front side and markers on the fenders are not working. (rear is working) (new headlights with new modules installed)
* brake lights are not working (3rd brake light is permanent on when ignition is on (new brake and clutch sensor installed and learned) (BCM front Fuse box front Fusebox Engine compartment are brand new) and in the trunk is also BCM think for convertible and other components also replaced this (second hand) all fuses and connectors are cleaned out.
* convertible roof is not working (when i press button nothing happens also no warning or faults in the module).
* both front seats left and right can not move forward or backward but the backrest adjustment is working on both sides.
i brought the car to the opel dealership but i have a feeling that this guy not now so much about programming he could not fix the programming and also the second key is now also not recognised anymore i dont know what he did but both of them worked normally before he played with it.
i want to pay for this service i want to fix it as soon as possible i hope somebody in this forum can assist me or sort this out for me.
On ford transit 2011 sid208 After cloning ECU I have only this B1206 code. No crank. Checked inertia switch all is good. Power is coming to pin A9 trough inertia switch. Found on forum some threads where it happened to others but I cant find solution. Old ECU was dead due to water damage. Is there anyone with solution . Please pm me... Thank you.
Hi everyone,
I need a XML Parametrization file for Audi A6 4G air level control module. A workshop tried to calibrate the level and deleted the adaptions which resulted in deleting the parametrization and dataset. I tried to do it online with vaglogins GEKO and it didnt work (I think it was some error like failed to retrieve data or so). I also tried to use the xml generator from vaglogins to use with ODIS E which worked fine in the past but it only gave me Repairadvice xml
I can do one byte change and car will runs any km ,after car off, car will not start again. After second (again) read EEprom have corrupted eeprom.Rewrite eeeprom ,again runs any kms,car off - not start again. (30KM) ~
I think ,they changed the checksum construction between mpc and flash
Rewrite eeprom ,again good till car ign off (30km) or +- 30mins
Sgo reflash tested same
BDM reflash tested same
Full backup reflash original tested same
Eeprom immo off tested same
From different cp34 ecu writed eeprom with immo off tested same
Any patch?
I have this airbag ecu from a Seat Arona, with fault B2000 (Internal Fault). Also it has a lot of passive/sporadic faults which can´t be erased because of B2000.
Ecu reference is 5QF959655S. It has an Infineon TC234L-32F inside and read it with VVDI Prog.
Could somebody, please, take a look and repair file? I´m almost sure it´s file problem (maybe checksum)?
Hi,Customer has replaced cluster on his Crafter 2006 , 2.5 TDI. Car starts and run but KM shows ——— after ignition.
When I try to perform replacement procedure or write new kilometres, using ODIS, it asking for online connection.
Is it possible to synchro cluster to EZS and coding cluster remonty using ODIS ? Thanks
Hi. I have a customer with non start due to adblue fault P241D.
He's changed tank but still error .
I've tried to do resets with Forscan and Launch but saying conditions not right.
Has this got to be reset by Fords only or what diag tool can do it ? Thanks
