Hi, I found and bought a cheap M113 4.3L engine out of an S430 w220, complete engine and belonging gearbox, planning on putting it in an older car like a w124 or something, but I could find very little info online about this ecu, does anyone know if its possible to make this standalone and immo off, or do I have to go aftermarket efi? I believe its bosch ME2.0 or 2.8, Bosch nr 0261 206 056. Mb A025 545 88 32. I pulled the engine myself from the scrapyard, keys where not available so do not have key or eis. If im doing this conversion, im planning to use aftermarket tcu, so ecu need to work without stock tcu communication as well.
Have kess/ktag if that will read this ecu, have not tried that yet, no use if I cant find anyone to help make standalone.
Hello,
I have a problem with EDC17CP55 of Range Rover Sport.Someone tried to do chip tunning. The ecu stores fault P064F Unauthorized Software/Calibration Detected. Engine dont work properly. I tried to reprogram it with Launch, stores same fault after that. I bought original file, but can't write it, because OTP sectors. Tried to clone it with Flex, but goes to 90% and stop.
Is it possible to restore it or write original file to this ecu ?
I have 2014 Ford Focus MED17.0.1, I need to remove Cat+Evap, DTC is : P144A Evap + P2196 O2 sensors, also, please remove all O2+Evap related DTC like P0030 to P0079 or P130 to P179, P0400 to P0479.
Hi there, i attempted DPF off on my Ford Kuga, but unfortunetly when writing the file my kess clone says the checksum is incorrect.
had 2 friends send me a file , same issue, both pointing out maybe its because its a clone?
but here me out, im able to write the orig file back to the car.
whats going on here haha
The problem concerns Audi A6 C5 2.5TDI Quattro. The car is after changing the automatic gearbox to a manual gearbox. You can't code the manual gearbox in the ECU. The ECU is EDC15VM+ or MSA15. The flash is 2xPLCC32 128kB, XGecu T48 read as AM29F010, but these are probably OTP memories.
I read online that it is possible to add a manual gearbox to the flash, but this is beyond my knowledge.
Can anyone help with this?
What other possibilities are there?
ECU:
0281010152
4B0907401 R
2.5l/4VTEDC G000AG D66
I’ve bypassed the immo as it has gone bad preventing start, so the solution works on the flash using MRT (also tried Fixwave) however I am having an issue with removing the warning from the dashboard.
Could anyone assist me at all, or is it not possible?
we have 03L906023MQ ecu hw43
need a suitable frf since car has had its dsg box swapped to manual 5 speed flashed it with manual frf but was for a 6speed and cant code to 5speed. car has start stop
edit. running 023FS sw now but this is for a 6speed
Hello tuners. I was wondering recently if there is any way to change what displays on diagnostics like VCDS, etc... as ECU info. Especially the ECU VAG Number and Component.
I was planning to do an engine swap (EA111 engine to another EA111 engine but different power, they look the same from the outside) and i was wondering if i could change some values somewhere to make it say something else instead of this. So when for example the police stops me and checks something they can find a matching ECU ID with a different engine. I don't wanna go throught the hassle to make it legally because it's expensive and the engines basically look the same from the outside if you dont look close for numbers.
I just wanna make it look like a different ECU number. When in reality it's a different one.
Thanks!
Hello, did anyone managed to clone this bcm? marreli 952.
From my understanding it has a Fujitsu MB91F526LKC mcu i can just swap to a used bcm. does anyone know a connection diagram for vvdi prog to read this mcu in circuit? or another way to clone those?
thanks in advance.
2017 Audi Q7 with a known used and good front radar distance regulation sensor. Throwing code for component protection. Is there anyone that can remove this from this module. Looking for time it can be done and price. Thank you
Hallo allemaal,
Geen communicatie met motor-ECU (Valeo J34P-AEE). Koelventilator start bij contact aan, motor slaat niet aan.
ABS: dtc 4013, BSI: dtc U1318, U1000, U1308. Canbus lijkt fysiek ok. Gemeten met scope Can-H is ok,
Can-L is soms verstoord en verdwenen.
Ik heb een canbus(pin)-layout nodig en natuurlijk tips!
I retrofitted folding mirrors on my W176 2017, but my door modules are missing 275, 880 and U62.
Is it possible to flash the module for this? As the plug of the folding mirror can be seated. Everything is coded but it's non functional. If not, anyone knows the partnr I need for the folding mirrors?
