Hi guys. Wounder if someone can help me.. i have had a chip problem on my mainboard on ecu. bought a new one and wrote out Full. EPC and EPR from both old and donor ecu.. Managed to get it started but still have safe in dash. Also managed to remove the Tprot. but not sure how to do this right.. Is there anyone who can help me please. Adding all the files. Also added the file im using now marked in use. Dream had to be getting this work with the file im using(stage2 hc and lc, TPROT off) but not sure if it will be manageable..
Reading done with Ktag. would love to write with kess Though
I need your help with this guys, the back camera don't come up on the screen, the camera cover open at the back to signal it's on reverse but sometimes it shows and many times it doesn't, I have attached DTC report after diagnostics thank 🙏🙏🙏🙏🙏🙏
Guys i have Mitshubishi outlander with ecu 4N14 - RENESAS SH7058
275700-0724
1860B419
and cannot do egr off...
I can read / write with K-tag protocol 324 - car runs 30second and after die and write P0607 ecu faulty.
i can read/write with KT200 2 - read with jtag, write with bootmode same result.
When i write ori file back, car not have problem and run fine only egr fault..
can somebody Advice me or LOOK on software? its not do by me - is it from my flasher-friend.
Big thanx . i can pay something for working solution. Thx and Rep of course
3files in attachment:
1.ori read with kt200II
2.ori Ktag read
3.Egr Off from my friend.
hi i am looking after cda6 i need to install and remove immo from a old jeep wrangler 1998 2.5 gassoline ... i have micropod 2 if anybody can help i will pay
the car starts and stops and no dtc present
Hi guys, I am wondering if it's possible to use Mongoose clone for JLR SDD with Toyota tech stream software. I have successfully used the JLR cable for GDS2 and just want to confirm if the same applies for Tech stream as both Toyota and JLR clones are drewtech mongoose pro clones.
Thanks!
UPDATE:
Mongoose JLR works with tech stream and tech stream has this cable as a selectable option.
I have problem with astra K 2020 year 1.5 CDTI LXD engine Delco E45 ECU. adblue sistem flashes on dash and i says car has 800km to nonstart.THere is no error in engine ecu.I tried with adblue resset but error remains.I have launch in gds2 there is no 1.5 cdti engine.
Hi all anybody got a workshop manual or wiring diagram for a 2010 Renault Scenic mk3. looked on here https://newdialogys.renault.com/ but you need to be a company to register. thanks
Hello members....I have problem with deactivating dpf with this car.Ads solution not good.
Othetr switch solution doesnt work too.Have somebody working solution?
thanks.... here is edc17c42 1037531043
Customer call today that eps fail and error in dash..car still rus start fine but steering failed,way to hard to drive....I search all over net and see this eps is coded to car uch...
is realy eps part of immo system..because then I need to prepair it to be virgin BEFORE connect to car..or I can put new ( used one from other car) in car and then play with it via obd..
need to make this homework before customer brought car here..
Hello, i have this Sharan 2002 edc15 and the owner changed automtic transmision to manual!
On slow speeds the car has some hard bumps, does anyone know it can be corrected from sowtware , the coding is already made!
Thx!
Hello Everyone. I need an original input for the Autoliv 608361600E - 8200969856 airbag sensor. Opel Vivaro 2010, 2.dci van. I have a problem with error B0003. The car only has a driver's airbag and a driver's pretensioner and a passenger's pretensioner.I have already replaced two other sensors with the same numbers and still B0003.
The original controller from this vehicle. Please help. Thanks.
Hi all,im looking for a solution for EGR off only for a range rover sport 2.7tdi i have attache the file read with Kess v2. any help appreciated. thank you
Can someone help me understand what exactly needs to be done when going from CXX to FXX (AE to AL) mechatronic?
Can I simply install a FXX (AL) mechatronic with any FXX (AL) software (but tweaking it to have my gear ratios)? Or is there some other information from the CXX that needs to be copied as well?