Does anyone happen to know anything about encrypted efi live files not allowed to be flashed pass thru only stand alone with v2 or v3 are they able to be by passed or unlocked ?
I need to read/copy the Uconnect data in a 2015 EU Fiat Freemont (Doge Journey). I think the nav is Garmin. I have tried AlfaOBD Back-up to external hard drive with different formats and sizes, but it always says that there are ECU(s) with values out of range. The flash drive does show up when connected to the center console.
I have removed both the CSD and radio unit and opened them up, but I don't know where/if there is a hard drive and if it's possible to remove and read.
Out of curiosity can HP Tuners do a delete on older 6.7 Ford powerstrokes? I noticed if I use a older version of the editor I can disable all the associated DTC. But will that keep the truck out of derate? And do you have to do anything with the EGR mapping? I'm a little confused because there is no radio button and I'm NOT experienced with tuning at all.
I'm tring to access to HLI_FL176 HLI_FR_176 in W117 car. I can connect using DTS Monaco 8.16, can read DTC.
When i'm tring read to Variant Coding i receive: error: PDU_err-evt_rx_timeout: receive timeout for consecutive frame, receive aborted (65633)
DTS Monaco 8,16, Win11, Pass thru - OpenPort 2.0 Tactrix,VAS5054a, W117 Facelift
Could You please help me/provide me to resolve issue ?
Hi All,
I have a Eu w221 Command unit.
Thr Nav has never worked since I got the car .
The Dvd Cd changer was working partly , then after a lot of connecting and disconnecting of the changer eventually it has stopped working- no response from front any of the front panel buttons. I got a replacement unit which is a US unit . Swapping the working DVD changer drive to the Eu unit - still no response .
I have attached screenshot of the Eu and US units in Eng Menu.
Can anyone tell me if the missing components in the Eu unit, ie DVD changer , decoder , Hard drive , are Hardware faults- bad Ecu s or Software - reflash in Telematics would correct?
Hello. I have a problem with my VW Passat B8. The car drives normally, does not lose power, but the check engine light appears. This is an error related to DPF efficiency. Please help me explain what may be damaged.
Hello friends, can someone tell me which map is for sports in the file? I have a stage file, but I just can't get it to work so that it only pop on sports. It would be great if someone could tell me the map, for all mods it work but only need map for sport
If someone could modify the file for me, I would take a look at it with ECM Original.
Hallo all, i have a W220 EIS A2155450608 key doesnt turn, when reading the eis it looks like a virging EIS but i had seen this before on many W203 EIS but never a W220 EIS.
The EIS has 2x 4J74Y MCU's.
I attached both mcu eeproms here, can anybody help with this eeprom?
Hi
I'm really struggling with this problem. Completely out of ideas.
2014 Disco4 (L319). These DTCs come up at ignition ON:
TCCM: P186D-00 Clutch actuator stuck
TCM: P279D-02 Four wheel drive range signal circuit - general signal failure
I've tested the wiring from TCCM to transfercase, all ok.
I've tried a 2nd hand clutch actuator, although the original actuator works fine when 12v applied on pins 1 and 8
I've tried a 2nd hand TCCM module
I've tried a new solenoid
I've tried a new position sensor
There are no metal shavings in transfer case oil.
Performing adaptation of actuator, solenoid, or transfer case, they all fail, without any apparent movement of actuator.
Hello everyone,
I'm encountering an issue while attempting to reprogram a BMS20PT30 ECU using Monaco. The car is a w177 250e Here's the process I've followed step by step:
I enable the Ethernet and make sure DoIP is connected.
I disable the firewall on the EZS167 (setting the access to 39).
I request the reprogramming seed from the BMS20PT30 module, calculate it, and successfully input the calculated seed without any errors.
I then go to the Flashing tab, load the necessary files for programming, click Prepare Flash Programming, and hit Run.
However, I get the following error in the log:
Code:
SEVERE Code: 51712, CodeDescription: JobError occurred
VendorCode: 21160, VendorCodeDescription: Position: SecurityAccessViaJob > MCDError: Could not find the shortname "Security_Access_Reprogramming" > error while executing security access null
Here's the relevant part of the log:
Code:
2024-11-22 16:20:38 SEVERE Severity: eERROR
2024-11-22 16:20:38 SEVERE Code: 51712, CodeDescription: Unknown error code
2024-11-22 16:20:38 SEVERE VendorCode: 21160, VendorCodeDescription: JobError occurred .21160 Position: SecurityAccessViaJob > MCDError: Could not find the shortname "Security_Access_Reprogramming" > error while executing security access null
Could anyone please confirm if I'm following the correct process for ECU reprogramming in Monaco? Is there something I might be missing or doing wrong? Any help or guidance on what could be causing this issue would be greatly appreciated.
Thank you in advance!
Posted by: krum.87 - 11-23-2024, 02:18 AM - Forum: Selling Box
- No Replies
Fassi Crane Softwear Fasslim D4 FX800 LMI systems 500 euro Fasslim D6 FX500/Fx900 LMI systems 550 euro
No keygen need it
PayPall Secured transaction
Contact info [email protected]
I'm using OPCOM China-Clone 08/2010 (firmware version: 1.45, PCB version: 6.0). Overall I am happy with the device, I can easily handle most of the problems in older Opels, but I cannot connect to the Instrument (to read errors, reset) in most of the supported cars (e.g. Opel Meriva A 1.6 petrol) - it loops when trying to establish a connection. I know that the problem is common, but I cannot find a solution on the forum. Has anyone managed to successfully solve this problem?
I would be very grateful for specific suggestions.
Got an old Mitsubishi Colt from 2005, can someone provide immo off for this old one? Because car won't start with original keys anymore.
Much appreciated
Hi mates.
My left low beam is few secound blinked and stop working. Dinamic turn, DRL and high beam work normaly.
Is it the ballast or the LED module from the low beam? What does the LED module (bulb) even look like?
This happened to me today and I didn't have time to remove the entire headlight. Any help would be appreciated.
Hello all,
Is it possible to install just to install individual modules of the Telematics update. I have a US command system for w221 and I am looking to get the Video DVD player menu option update with out having to Update the entire command unit. if it is possible can just this update be burned onto an installation disk without having to use DAS etc?
![[Image: pin-edc16c34.jpg]](https://i.postimg.cc/d78vY3Fm/pin-edc16c34.jpg)
