Hi, please help with dtc off P0420
Toyota auris 2013
1.8 hybrid
denso 89661-0Z750
SW Num:.302U3100
.SB1MS3JE5
HW Num:ZWE18# 2ZRFXE..
Part Num:**-0Z750.
Hey, i lost my old ecu and have now bought a new used one, What Can i do to make it work with the cas and Keys without doing immo off. I Will gladly pay for your services, let me know What you need to make it work. Etc the file, some Numbers you name it.
Hi i have an old good quality mpps v3 upraded to v5 (cable EU version). now if i install the v5 says error1, device driver wasn't reach.. i remember that there's a fw upgrade. can someone provide this tool? ....in Origin was v3.0.2.37
Hello, if someone is so kind as to send me the file of an ecu and an uch t4 of a Renault Trafic 3 I would be very grateful, if they are from the same vehicle please, thank you.
For sale my ECU collection from Delco & DCM3.7AP
I bought these control units brand new and read about resetting used units
If you describe the used unit with these files, you can then program the used ECU online with PLC or OpCom and you will receive the original FIN and KM data again (it is not possible otherwise.... Except Immo Off solution)
The collection cost me around 10,000 euros. I'll sell it for half.
Hello Members,
I have a Sprinter 2017 (906) 316cdi 163hp from 2017.
I wanted to ask if it is possible to do speed limit in flash read (or eeprom) to set speed limit to 130kmh.
I know with Xentry (Vediamo, DTS Monaco) Speed limit can be set, but I dont have Multiplexer and Software ) also no VCI SE or similar tool, so maybe there is a file solution.
I do have a Launch x431 V+ but from 2020 (I dont know if variant coding with this device is possible because dongle is 301 and not dbscar7 or similar and I dont know if this is possible with this older Launch device to code (I did not try).
I attached flash file, maybe someone has a hint, or can help.
Hello. Can someone check it? The customer came to me with the warning light on (the glow plug light) but no error code appears on the diagnostic and the car is emitting excessive smoke. I'm thinking of starting with EGR off. The turbo is working properly, it's been checke
I have a problem with a Mercedes S500 3.5 v8 W221 FROM 2006 Bosch me9.7,
The calculator is h.s I only managed to recover just the external flash and the eprom, the internal flash MPC unrecoverable, I ordered a replacement calculator second-hand for the same vehicle.
I wanted to know if I just swap eprom 95080 if the vehicle starts?
Need some help...2001 manual Jetta ALH...Can someone tune this for a 4 bar map sensor, Bosio PP 764 injectors, and a GT1756V turbo? Will pay for solution..Thank you
Hi I’m looking for some sort of software or tool that can program modules on Ferraris? I have a 2006 that needs a new transmission module (TCU) and I’m not sure what tool would need. Would Autel be able to do this?
I have a 2017 Jaguar F-Pace with the 2.0 turbo diesel engine. I continue to have issues - Fault Codes - P249D. ( Closed Loop Reductant Injection Control at limit - flow to low). SCR NOx Catalyst Efficiency below threshold Bank 1 Catalyst 1,
I have had the dreaded " Diesel Filter Full" warning 2 times in the last week. when i do force regen the filter always reads at 30g. somedays its easy to get it down to 6 however other days it takes a hour or more while driving.
The Turbo, Timing Chains, DPF canister / filter, DPF Dosier Injector , Def tank and pump, EGR cleaned, all nox sensors replaced and still have check engine light on for
I have used SDD to reprogram and reset all adaptations... etc.. nothing is clearing these out.
good day to all
I have a boot mode ecu (CRD3.1 ) in use vediamo. The original file was not readed.. not ori file and ori cff file name...
it in boot mode.
i can see 3 invalid sw blocks. My problem is... I can´t find these cff files name.
Anyone knows the name of ori cff files to flash it (firmware update)
i need ori crd3 cff file name.
Hello guys,
I need help here please.
I read ECUs of two cars, info attached.
Same model, same engine.
The first car (DPF off + EGR off?) I read with Kess (tricore boot) and Ktag without any problems.
The second car (Mod file) gave a checksum error after reading with Kess and Ktag but I managed to read it without any errors (I used a modified Ksuite.exe that disables checksum) it was the only way to read without any errors.
I think the files are ok.
Any protection from the previous tuner after remapping the car?
I don't know who it was because the car was bought with the mod, the car works perfectly and has never had any problems.
The files are different versions and I would like to know if there is a way to use the modified file in the car that I think has DPF and EGR off because the car have some problems and I suspect it is the file.
I don't have software and enough experience to check.
I don't have original files and I'm trying to solve the problem and get the car as good as possible.
All help will be appreciated.
[font="MHH Font", Calibri, sans-serif]Hello, need help please to delete a DTC on a map, with diag here is the DTC to delete, DTC187391, the car is Renault Talisman EDC17C84, thanks[/font]
Hello everyone.
I have question .
Can i read bmw 650i 2005 v8 with kess clone ?
If yes can someone do for me hard cut limiter please ? As there is soft limiter and when you rev it bangs once and drop rpm .
Just wondering if anyone has any experience on calculating the pin code on these sigma alarms using the eeprom dump? I'm interested how to read the pin code from these dumps.
![[Image: stkob5q.jpeg]](https://i.hizliresim.com/stkob5q.jpeg)
