Hi pleas need help now if it possible W213 swap digital cluster from chaina and need EZS and ic synchronisation i have xentry vidiamo monaco allredy connected .Thanks
Hi guys. i have a bit of problem own peugeot partner 1.6 hdi with EDC16c34 bosh ecu. old bricked due to my stupidity not doing BDM read prior to fiddle with clone kess2. i managed to source replacement flash and eeprom make it stage 1 egr delete and immo off and it work fine. however for some reason i have abs communication fault even thou i dont have abs and dash not showing speed at all. wander if someone have a solution for that, able to help or guide me of what to change. in attachment read out of both eeprom and flash
[font="Fira Sans Condensed", Calibri, sans-serif]Hello guys, can you help me with ori file FOR EDC17C10 CITROEN 0281 019 817 9805947380[/font] [font="Fira Sans Condensed", Calibri, sans-serif]THX[/font]
How its possible to activate the EGR again if its made Off by another person.
I Don't have the ori file and wants to activate it.
Is it possible to do this with DaVinci?
I have the original VAS6154A interface which PIWIS does not see. Does anyone have knowledge of what driver is needed or PDU-API to make the head end visible to PIWIS?
I have 2011 A4,mmi radio etc works but nav doesn’t work.
It says 8 satellites found but says to insert nav data medium. I have sd card in but it doesn’t seem to work and I know slots are good! I don’t know if it is 3G/high/low etc.
Can anyone help me get this to work?
It says Bnav_EU_p0054_D1
Nav databaseblank!)
I have sd card 5Na 919 866H
On engineering it’s saying Train version p0054
MU software 0147
I also noticed when nav starts screen sometimes it loads until 25/26% then nothing
PS please delete post I got the solution on another forum
i might be looking for a tune for my truck. Its 2011 Tacoma with the 4.0 V6 1GR-FE gasoline engine. Roughly 236hp. Not looking for huge increase in power, but more low end response and better transmission shifting points. Let me know with what you have
I found solution somewhere for defective ezs module. They say, its enough to cut red/black wire, which is going to module. Before cutting anything, this will solve my ignition problem? I understand, that steering lock will not longer work. I don’t have problem with this.
hello , can someone make it virgin or elv off + dtc off vvdi prog read out i misread the warning about not running the elv replaced if the hardware wasn't present as "THIS WILL DAMAGE THE WCM" witch alfa obd, i never have elv at all in the car SKIM error and it won't turn over. Locks and unlocks but won't start. WCM screwed from running the ELV replaced. The ESCL stated parameters out of range. need elv off becouse not exist in usa model and dtc B2254 RAM Code - Column Lock Module Internal (Wireless Ignition Node (WIN) does not receive the correct response message back from the Steering Column Lock Module (ELV)) but i never have elv at all pin code 9127 or make it virgin , i belive need remove pin and vin but not sure , if some one done it before may be can help and explain i do it myself . i found some info but not sure how to use : "data flash 64k. immo code repeat 16x vin code repeat 16x 4blocks x 4 positions +1 CONFIG: 4BYTES BYTE1: boot block (0x00~0xff) BYTE2~4: 0x000000 (default value) " what does it mean ?
module and car info 2014 Chrysler Town & Country VIN: 2C4RC1CG4ER418006 PIN: 9127 p68105738AE
T0000131470136 ID:C437B046B3B337B6 renesas v850 D70F3629 read out vvdi prog
virgin of dtc off and elv off
if posible to do skim off and work too , i did skim off in pcm already but not help .
Hello i have made bridge to read the abs code from the car ,i have 1 4 3 3 flash from abs light what is the problem to the car and after i have 1 4 3 4 flashe*s
Hi
I have in service VW T5 2011 2.0 TDI 132KW Manual transmision,ENGINE CODE-CFC
Car is lost engine ecu in crash,i dont have backup,im buy ecu with same part number,but ecu is from Automatic gearbox
Im read instrument cluster,and compare immo data,car start direct on starter relay,and work,but cant start normal on key,and have dtc "lost comunication with tcu"
PART NUMBER IS : 03L907309H
0281016270
I need fullbackup from manual gearbox
im try flash with odis,and i have .maps from manual gearbox,after write,same problem
hi everyone
can domeone make this file iwanna SYNC the ecu edc16c34 with BCM for car volvo cx90
the car can't move now and i have some default in the diagnostic so i wanna know if it's the problem make the car like that ( you can find it in the picture)
Hello. Is the [font=BlinkMacSystemFont, -apple-system, "Segoe UI", Roboto, Helvetica, Arial, sans-serif]SUPER MB PRO M6 compatible with c4 ? Work this with an old MB W210 Bj 97 ?[/font]
Hello colleagues!!!, I need your help... I need to unlock 2 keys 8k0959754d for an audi a6, but I tried with the tool I have and I am not able to, I have an autel im508 + xp400pro. but I don't know how to do it. I have downloaded the eron and the eeprom for the key but I don't know how to load it with the autel.. can anyone help me?
Xhorse Key Tool Plus Practical Instruction - Practical Guide for Vehicle Maintenance Engineers and Locksmiths
Product Description:
The KEY TOOL PLUS Practical Instruction book includes an introduction to the KEY TOOL PLUS tablet, basics of working with vehicle IMMO systems, and tips for using the device. The book provides a detailed description of the car key matching process based on real-life engineer operations, along with safety precautions. This guide offers technical support for engineers involved in IMMO setup and helps avoid operational errors.
Product Features:
Helps beginners develop engineering skills.
Assists engineers in advancing to senior-level expertise.
Minimizes losses and saves time.
Download Link
The files are indexed for search and password-protected.
To get the password - click reputation +
To speed up the process of receiving the password, write me a private message.
Messages about receiving the password in the topic will be ignored
Hello, I have Porsche PCCS account and software, but I have problems with VCIs as passthru (using Texa Multihub and Scanmatik) both doesn´t recognice ignition status and wont show me any Ignition switch emulator, so is there any Ignition swith emulator that can I use on PCCS? Or any VCI that works 100% with PCCS?
I have a customer that have a audi S3 where the oxigen sensor after cat had make a short cirquit.
Now i have on the ECU the Fault codes : P1631 signal too high and P1634 signal too high
i read a lot that these fault codes commig because of the short circuit of the oxygen sensor.
Now i wanna repair the ECU but i need to know what is the problem on the board, i havent found till now what need to change.
I have also attached a photo of the board of my ECU, I have some similar ones where I could re-solder the components if anyone can tell/show me which one it is ?
Information to the ECU:
Bosch ME 7.5
0 261 206 794 (8N0 906 018 J)
i also see on the bosch compatibility tool that i also can use a ecu with the Bosch number 0 261 204 875 (they are a lot cheaper to buy) but i am not sure when i order this can i flash the full backup on this ecu and it is fine and work again? Is this right or what need to change also that this work ?
Toyota ECU data is free to share, no password required。
If it is useful to you,
please don't forget to rate with thank you。
Includes a list of files, some of which are not listed on the list，The list is for reference only。
The size of the compressed package is 6.5 GB
If it is useful to you, please don't forget to rate with thank you
blank!)
![[Image: rLvFQx4.png]](https://i.imgur.com/rLvFQx4.png)
![[Image: 5YK0nSF.png]](https://i.imgur.com/5YK0nSF.png)
