I have done several CRD3.10 ecu's with bitbox Without Problems (TC1797). I have the Delphi Diesel Can Module.
Today I wanted to read a CRD3PLUS.A0 Ecu (FID: 214) (on Bench) and I could not even do the identification with bitbox. Pinout is 100% Correct and all the Connections as well. Im using original scanmatik 2 pro + pcm combibox. Everything in the combibox is set to Automatic as I usually do with These ecu's. To be sure that it's not a Connection Issue, I have removed the Ecu of my own car and tried to read it (CRD3.10 ECU) with Same Setup and it worked like a charm.
In the Module Description from bitbox it sais "CRD3.xx"
But can you also read CRD3PLUS.A0 with bitbox?
If yes: I will need to check my cables (combibox + sm2 obd etc.) - Problem is somewhere on my side then
If no: Can PCM Flash Module 91 Read CRD3PLUS.A0 ? PCM Flash sais in the Description: "CRD3 / CRD3P". So I guess the "P" Stands for "PLUS" and this should work..?
I Need to fix the car asap as it has 5 Kilometers left because of AdBlue issues, the Engine wont start and the car is basically a brick. NoX Sensors etc have been replaced before already etc.
Car is a W205 C250 CDI with OM651 Engine from 2014
I would highly appreciate if someone could Tell if bitbox is supposed to Read CRD3PLUS.A0 or not, so I can continue troubleshooting my Setup, or just buy the pcm Flash Module 91 for it and get it done
I've got an easydiag 2.0 new serial head, had it since new.
Originally had offline brands, changed to Diagzone and then for the last 2 years I ran XPro5. My sub ran out a few months ago and I didn't rush to renew as I was out of the country, then went with a new supplier and renewed, downloaded the program update and the new firmware, updated to v12.14.
Since the update I am getting serial discord error or software damaged depending on what im trying to run, cars for example are software damaged and things like EOBD are serial discord, nothing works.
I've tried factory reset of the tablet, trying older versions of the apk and downgrading the firmware, I've run out of ideas, any suggestions?
If I put Diagzone back on the tablet it connects fine but XPro5 doesn't.
For my W 164 there's a very suspicious SW 0009024455 and I have rough up and down shifting. I have activated Agility and Sport modes and A the only possible mode where shifting has only minor deficiencies. So now I have A-Sand E modes with the last one being weird too.
I might be wrong but the latest SW for my car should be 0009024721-001_CFF. and my current SW seems absent in all sources available for me. Looks like a custom SW
Can anyone confirm my SW selection given the following:
VIN: 4JGBB2FB1BA658717
ETC: 0034460310
EHS:2202700060
VGS3_0402
VGSNAG2
I have bought it a couple of weeks ago from a used car dealership in Richmond, BC quite recently and the dealer claims he's not aware of any SW changes being made.
I am looking for an experienced and professional partner to assist me with the installation and use of diagnostic and coding software for various
VAG software (ODIS, VCDS, etc
Renault
mazda diagnostic
opel diagnostic
ford diagnositc
another car models
Additionally, I require support with coding tasks, particularly for BMW, Mercedes, and VAG vehicles. I am looking for someone reliable, available 24/7, who can assist me with coding issues as they arise. It is important that the person has the necessary expertise, works professionally, and offers fair pricing. Long-term collaboration is
If interested,
I'm performing an M57 swap in a BMW E90 320d that had an N47 engine with a DDE 8 512 047 (a EDC17CP41 if i'm not wrong?? ) ECU , HW 0281017520 , and would like to repin the body loom plug to match the M57's ECU which is an EDC16CP35 - DDE 7 803 369 - HW 0281013500
I'm struggling to find the complete body connector entire pinout, i'm only finding the pinout for bench operations which doesn't serve me at all, The engine and ecu are from the same donor car so the engine connector doesn't need a repin,
Shipping options: Link to download from fast server
More information PM:
Compatibility: Operating System: Windows XP 32bit (x86),Windows XP 64bit (x64) Windows Vista 32bit (x86), Windows Vista 64bit (x64) Windows 7 32bit (x86), Windows 7 64bit (x64) Windows 8 32bit (x86), Windows 8 64bit (x64) Windows 10-11 32bit (x86), Windows 10-11 64bit (x64) Mac,Android
I'm using MBSeedKey (have also tried SeedCalc 3.0) and can't seem to find a valid DLL for my ISG48v1 module. It needs an 0B level security unlock but the ECU I should assigned to that DLL is CEPC253 and the 0B level key it creates is invalid for ISG48v1. I looked all over but can't seem to find this DLL, anyone have it?
Good day. I'm new to 17.5.6. On 17.4 I could change FLASH without changin EEPROM on citroens, but here is VW... So...
Friend of mine has a car with damaged during crash ECU. Now ECU died.
Step 1. Replaced old ECU 07K 906 055 CR with used 07K 906 055 F, stock firmware, immo off. Car started, but TCU does not recognise firmware so does only 3rd gear in emergency mode.
Step 2. Successfully read old 055CR ECU flash, eeprom & transferred to used 055F ECU. Got DTC 005642.
Step 3. used 055F flashed with ORI VIRGIN EEPROM (made with VVDI2), adapted to car. Still have 005642.
CS are correct. R/W with PCMFlash.
Any assistance or advise highly appreciated.
Attaching: old ECU, new ECU, new ECU made virgin & then adapted to car.
Hello
I need help - Glass roof added to Mercedes A180 W177 2018. I cannot change the VIN in the TSSR177 server. I tried Dts Monaco and Vediamo.
Without Vin I can't calibrate/move the PSD.
I will sell a Dell rugged 5414 laptop fully functional with a charger and interfaces for servicing cars from the Vag group. Odis S Odis E Elsawin 6 Etka and Vcds 24.7 installed. All programs available in three languages Polish English and German. Price 470 euros PayPal payment
I am working on a new project aimed at retrieving 32-byte sync keys for Audi A6, A7, A8, and VW Touareg models. To achieve this, I need unencrypted BCM2 files that also include the key EEPROM file, either 32 or 512 bytes.
If anyone is willing to help and can provide BCM2 Pflash, Dflash, and the key file for these models, please share them in this thread. I appreciate your assistance in advance, as these files are crucial for my project. Please provide only BCM2 files that include also the Key eeprom file.
I need to code the replaced odometer audi 2015 usa. I bought the used odometer, in the European version. Who can do it remotely, please contact me via PM
I have working ODIS 7.2.1 and VAS504A (also i can share vas50504a via internet)
Hello people,
recently I bought very well preserved Smart ForTwo 2002 but I can't find code for radio CD.
Manufacturer is Grundig.
I attached two pictures because I don't know which information is needed.
If somebody can help I would be very grateful.
Hello,
I am trying to get a C3 working under Windows XP with Vediamo 04.02.02, but so far without success. I already read through https://mhhauto.com/Thread-Vediamo-04-02...d-analysis , but couldn't get it working.
When configuring the hardware, Vediamo Start Center doesn't provide a serial number of the C3 and the list with hardware channels is empty.
Can anybody help me fixing it?
HHTwin is working fine, but doesn't serve my needs.
![[Image: bvdnyt1.PNG]](https://i.hizliresim.com/bvdnyt1.PNG)
![[Image: mas.jpg]](https://i.ibb.co/LCmqwnV/mas.jpg)