Hello, i try to increase vmax from 90 to 99kmh but doesnt make difference. I unlock ezs167 with dts monaco, then unlock cpc_ng and change vmax, it changes from 90 to 99 or 105 (from dropdown menu on variant coding), but always limited to 90kmh. Vehicle has tachograph, can it make difference? Engine is new om654 2022my.
Good morning guys. Normally I do not work on jlr but I am trying to help a relative.
Some modules have been changed on a 2019 discovery. The only doip tool I have is vcd fx. Is it possible to have someone to connect remotely and program modules using vcd fx?
I am asking as I am finding mixed information on the net.
Hola.
Necesito eliminar el DTC 2530. Envió el mapa original a 4 empresas y no han podido eliminar el código.
Por favor ayuda, adjunto el mapa original y 4 modificados que no funcionan
Gracias
(10-23-2024, 10:06 AM)XAPPO Wrote: Hola.
Necesito eliminar el DTC 2530. Envió el mapa original a 4 empresas y no han podido eliminar el código.
Por favor ayuda, adjunto el mapa original y 4 modificados que no funcionan
Gracias
hello.
Sorry, I sent the message in Spanish by mistake.
I need to remove DTC 2530. I sent the original map to 4 companies and they have not been able to remove the code.
Please help, I attach the original map and 4 modified ones that do not work
Thanks
I have a pretty complicated issue here and I am seeking help.
I have 2020 CX-5 with P0171 code, which I can not find the reason.
I checked everything that I would refer to as lean mixture, replaced sensors, and checked air leaks. Everything seems correct, all parameters are within specs, but LTFT is +25 and does not decrease from +20 when the accelerator is pressed, even with WOT. I also noticed that the Fuel Loop would not close and on Live data Closed loop indicates error value, I think it is because the mixture is always lean, but it could be the opposite.
The background if the vehicle was: when I got the vehicle it was dead, the battery leads were mixed. So I replaced a bunch of shorted modules, except PCM, which was already replaced. However, I reprogrammed it and reconfigured it with MDARS, but no result.
At this point I am out of options, but to replace the PCM and reprogram it again.
So friends if you have any suggestions, please advise.
My electric hydraulic pump b makes a noise when it switches on. I want to know how to code it off. I want too see if transmission will last. I like it quiet.
Hello, members!
I want to increase oil pressure at idle and at low rpms(I want pressure setpoint at 3000mbar in the range 1000-3000 rpm) I've tested the car with oil pressure regulator unpluged and the pump generate 3500 mbar at 2500 rpm the car is AUDI Q7 3.0TDI EDC17CP54.
Does anyone have solution for it?
Regards
![[Image: PXL-20241022-165421892-2.jpg]](https://i.ibb.co/nBqxTkL/PXL-20241022-165421892-2.jpg)
![[Image: toyota-epc-052024-19.png]](https://i.ibb.co/kGn59x5/toyota-epc-052024-19.png)
![[Image: toyota-epc-052024-20.png]](https://i.ibb.co/Wxkn0bV/toyota-epc-052024-20.png)
![[Image: toyota-epc-052024-21.png]](https://i.ibb.co/NrhtMqC/toyota-epc-052024-21.png)
![[Image: toyota-epc-052024-1.png]](https://i.ibb.co/fScpHKk/toyota-epc-052024-1.png)
![[Image: TOPDONRLinkX7forBMW5.jpg?v=1729589808&width=493]](https://www.vxdas.com/cdn/shop/files/TOPDONRLinkX7forBMW5.jpg?v=1729589808&width=493)
