I have here Citroen C3 II from 2015 1.6HDI and need to adjust mileage in BSI. BSI is VALEO ev-X04-00 9666952280 with 24c128 memory. Original is 275516 km and I need 123724 km. Original odometer is bad and I have donnor odometer with 123724 km (somebody glue PCB board to plastic housing so I have only one try) and I can not adjust odometer. I have try NYO he reads old mileage OK and if I put new mileage he also reads it OK. So, because I have only one try I have connect BSI on bench with FVDI and press read mileage he always reads old mileage 275516.FVDI have write option also if I put new mileage it writes BUT only untill I remove power after reconnecting same old milegae. So, where is my problem? Is it in bad calculation from NYO or FVDI reads mileage from different area of eeprom? If someone done this type of BSI with success please help here.
I also have BSI from donnor car (one that odometer is from). I will put that eeprom too with 123724 km 100%.I have even try to copy mileage adresses from that eeprom to mine but now when I read value with FVDI it gets 0 km.
Hello brothers
I have problem with my car ecm flash damaged lloking for
AM29F400BB
FLASH FILE
VOLVO S80 1999 6 CYLINDER NO TURBO AUTOMATIC TRANSMISSION
I have a OPEL ASTRA G 1.7DTI 2002, with damaged ECU, and I don't have the CarPass. I've read the dashboard, but it isn't possible to get the pin, as the ECU is damaged, and there's no comunication.
Is it possible to get the pin through the chassis number?
Replaced injectors with electrical connector for some months ago.
It's an MB E220 CDI 2006 model, 170ps.
Now i got an error and it's running on 3 cylinders:
204f - Test Electrical Line From Component Y76/2(Cylinder 2 Fuel Injector) to Component N3/9(CDI Control Unit) for Open Circut.
Hi everyone, I had a problem when flashing a 1.6 tdi caddy. I read in bench after the ecu got problem. And it seem that the file is corrupted. Does someone have a 03L906023PA full backup (flash and eeprom). The ECU had 0867 version and I updated it to 8011. I take any version please.
good afternoon im looking to find an old version of edc suite as current version cannot load new map addresses and i need to create svrl/popcorn. or someone who can add popcorn @4800 rpm on my file using winols or something
I need to get this cluster (e. g. 8W5920790D or similar, all the same..) working on bench, but I can´t find full pinout for it.
All I know is, that pin 29+30 is ground and pin 31+32 is terminal 30 (+). Pin 3 + 4 are for can low/high infotainment.
I have looked around and most people just ask other ones to do it for them.
I would like to learn and do it myself. I have MUT-3 SE in combination with J2534 Passthru. MUT-3 SE does not have an option to disable TPMS. MMCodingWriter is not supporting the vehicle.
That is why i search now for a solution to read out ETACS config file, edit it and then put the config file back in the car. I can not find anywhere the software named MUT Coding for download https://forum.kolyandex.su/viewforum.php?f=10
Could someone help? I would be happy to give a thanks and rep for getting some help or directions how this can be done on my own.
Hi, does anyone knows how work ews in BMW EDC16C31 ?? Actually i have a problem with swaped engine to Nissan Patrol. EWS is propably off, but engine not fire up. Fuel pressure on rail is 0. That ews block FRP? or ews cannot power injectors only ?
The ECU number 0 281 011 414
