Hello, can someone help me fix Mercedes GLE450 2022, 48v battery bms eeprom. Car is after accident, battery was discharged to 25v and locked up. Thanks!
It's a Citroen C8 2.0HDI, the car starts and shuts off, but if the key is held halfway between the ignition and start position, it works. I changed the lock, engine computer, bsi and bcm box and the same.
. Specifically, it just doesn't release fuel at the nozzles, and everything else is fine, pump pressure, rpm.
I changed the ignition switch, engine computer, bsi and bcm box and the same.
The rear right radar sensor on my W212 EZ2012 was defective, now I have replaced it with a used one. The active blind spot assistant doesn't work because when reading it, the error message comes up that the software on the control unit or sensor is not up to date.
Now my question: How can I update the sensor with the Star Diagnosis or where can I get an update file?
Hello
Today I try do adblue /fap/egr Delphi crd3 plus with davinci Deluxe but car dont have power.
With original file car running ok
Anyone have good solution for CRD3. PLUS?
Have a W166 pre facelift and was interested to know if current 7g+ gear could be coded to show in instrument cluster when in drive mode (as it does when in paddle shifters mode)? If so, what needs to be coded and how?
My car is a EU spec meanwhile from the search seems that US models do have this activated from factory. Did some research here but was unable to find such info. Photo attached.
Hello Mhh members. I am starting a tuning business, i want to know what the best begginer friendly software to tune cars is. I will ofcourse not test my files on my costumers cars, but instead having them tuned by a reputable tuner and then learning from those files. Which software would you recommend?
Hi there. Needing some pointers on a 7 speed 722.9 gearbox. i'm aware these have ben theft protected. My old one failed completely so could not download data. Purchased a virginised one, pre programmed with chassis number, SCN number etc. Installed it and it has somehow changed my dashboard display for gear position to the electronic column selector layout from the conventional display for a centre mounted propshaft tunnel type gear selector. I can now find no way to get it back to the original display and have ended up with a comm error code U040286 and a dashboard warning saying do not change gear - consult workshop. should the SCN number be the same in the ECM as the gearbox control module ?? thanks John
Hi, I try different immo off files but allways have problem, the car throtle very poor... someone have good immo off solution?? PSA solution not working, thanks.
Hello guys, i want to do dpf off in my ford transit 2,2 from 2014year, ecu sid208
ktag clone read this on bench, i patch backup file and modify patched ori mpc
i wanted to do checksum(always i do checksum in winols) but in this file winols say: no checksum available
i write moded file mpc and read only mpc to check if ktag calculates the checksum
could someone check if the checksum was calculated? I see there are changes, I would like to make sure because it seems to me that ktag calculated the checksum
Hi. I need help with change Pin and ISk code.
I try to clean immo with Renolink, but some how it remember ISk and PIN.
Actual ISK and PIN is :
ISK DAC414509C3C
PIN F9CEE7930BD5
need change with whis
ISK 582AB8C30852
PIN 4BE423AFD2B6
Hi to all i have this dashboard with 2 display that i want to read whit upa. MCU is upD78F0828B ca you please tell me whats the pinout to read and to power up on bench
hello . maybe someone can help ?
cas3 0L01Y eep corrupted .
someone was try to do something and
car lock unlock but dont recognise keys .
checked by soft and eep corrupted but unable to fix.
will add eep and flash
