Good day. I need to replace the dashboard of an Audi A3 and I got another one with the same reference number, numbers and letter.
Just copying the information from the 93C86 eeprom will copy the immo and km data, should I do something else? Or maybe just re-solder the eeprom? How do I replace it?
I been suffering for the lat 6-7 months, i have s560 w222. however i converted to s63 along with ECU AMG coding, and for the cpc.
when i turn on the car, after sometime it will show a yellow msg to add a quarter of oil, after it apears by short time it followed by a red warning "Oil lvl stop engine" i checked all sensors they are perfect.
to be sure that is coding problem. the Fuel range calculation isn't accuarate, my car fully tank goes up to max 800km. now it shows above 3,000km.
I need an expert to look into this matter please, job will be paid. no free things. to make it easier i got all tools, openport and DTS Monaco alrdy installed, just remotely check it.
is there any possibility to crack DTS9.04 like the 9.02 version? Ive got new Monaco projects, but with 9.02 it isnt working. I need 9.04. i have the Install Package for 9.04.
hi mates i face an issue here with bmw icom insta D , I BOUGHT ICOM NEXT A i use few days but unfortunately it doest open again and command me to activate licence to continue using it , so i look for anyone who can help please to activate it i have licence keys here down any help much appreciated thanx: INSTA D V 4.33.30.
Hui,
i have question about srs module form golf 7 with spc560p50,
ori module was water damaged and have a lot of errors with two of them about checksum error(167125-45,167125-79)
i have module form donor same part number, but if am right there is component protection,
dflash from ori module compared to donor looks like some parts are shifted and some parts are missing,
can someone help me with component protection, or repair ori file??
LAUNCH CRP919 EV Diagnostic Scanner Supports CAN FD, DoIP and 45 special function and 2 battery packs, supports ECU Coding for Electric Vehicles New Energy Cars, 120 models.
LAUNCH CRP919 EV Highlights:
1. Supports 120+ Electric Vehicle/New engry car models
2. Supports Battery Pack detection
3. Supports full system diagnostics+ auto vin+ active test + guided function+ ECU Coding
Hi, I have acquired an original Delphi DS150 with the security dongle. I have used a Chinese copy of the DS150 for the last seven years. I don't have a need for the fully licensed software (and it costs over 500€ for one year), so I have the cracked 2020 version of the Delphi software. Now I am wondering if I can use this genuine unit with my cracked software. Is it possible that I will brick my unit? Can I do a firmware update if the software asks me? Will the software even work with this unit? Is the security dongle needed?
This unit has been used this year (2024) with the genuine software.
Can anyone share a 2019+ version of an unlocked ESP177.smr-d file for flashing with DTS? I have two unlocked files, but both are from 2018 whilst my car is early 2019. When running the flash procedure, the procedure fails due to the variant not being identified.
Need help - need a full dump of the PDM and DDM modules from a Volvo s60 2011. There are many part numbers for these modules - I don't see the point in listing them. The main thing is that they are from the same car model (or at least the P3 platform) and are made on the HES Renesas F3371 microcircuit. Can someone help? As far as I understand, reading a full dump from these modules is only possible using a smok or i/o terminal. I have neither.
Hi there I'm Jorge Espino
I Need to do 8mmo off to a 2006 toyota corolla 89661-02k22 ecu whit eprom 25lc04a eproom because where in the middle of a engine swap.
Off course I pay the service via paypal.
I want to install in mercedes w211 COMAND BZ9880 from mercedes w219 but i need the pin code
VIN on W219
WDD2193222A152450
Serial number-512 AL988080815610