I have a Hyundai Tucson 2016 and need to check if AirBag ECU dump is correct or not.
I have only one error :
B148700 - Passanger AirBag short to ground resistance (2 stage)
I have check the wiring and they are OK, also i have check the passanger AirBag unit and it is OK
Now i want to know if this file is corrupted or is good. Maybe I have physical problem with AirBag ECU.
Below i have read the dump file with I-Prog
I posted probably yesterday in the wrong subforum here https://mhhauto.com/Thread-ETACS-TPMS-di...-it-myself
I think this is now the correct section to ask:
I would like to get the config file out of a Mitsubishi, then i need some software to edit it outside of MUT-3 because MUT-3 does not seem to show the option to disable TPMS, then i have to put the modified config file back in the car.
There was a free available config file edit tool available for free download but developer changed and now its not freely available any more. Its named: MUT Coding
I also have not found a howto for extracting config file from ETACS and adding it back.
This Mitsubishi model is sadly not capable to be configured with MMCodingWriter. MMCodingWriter is supporting in general TPMS disable but sadly not usable.
Would be great if someone could give me the hints what is needed to disable TPMS in a Mitsubishi.
Hello, is here anybody who can reset electronic steering lock to factory state? Would like to retrofit it into USA car which comes without it from factory. Used unit throws error durrng coding immo via Porsche PPN. Error is "password error" so i guess i need new one or reset used one to factory state. Thank you!
Hello, does anyone has taken airbag module of car? I need to access module to clear crash with smoks uhds on bench
I pressume it located under cup holder on center tunnel.
Does anyone know how to disasseble it to access control unit?
Hi everyone, I need help with a pickup I bought! According to the previous owner, it has a remap! I tried the car, it just smokes a lot, it has very little torque at low rpm, so I would like to get the original file. The tuner who did the service was at an offroad fair and I can't get his contact information! Can anyone provide me with the original file? thanks
Can someone help to write the NOX sensors off in a W906?
I have put aftermerket in the downstream, did the reset with xentry, tested it works normally, but after 30km the engine management light is on.
I read a lot of hours and spent money too to make it work my diagnostic, but now i am stuck.
I have a r230 and i can connect to the car but only for a few modules.
Now i need to work on ABC module but i see my tool only can read CAN-BUS modules.
I have a version of Xentry Passthru XPT 23.6.3 but i read on forums this version of software maybe can not read older modules via K-line.
I have a Ford VCM2 what is working with this software but i can not read the EZS, SYSTEM,etc and a lot of modules.
But i can read all modules with Autocom so the problem is in the Xentry - multiplexer.
I read about the HHT-Win is a part of this software and maybe it needed to work on older cars, but i am completely new in Mercedes. I came from BMW world.
I have a few devices like BMW I com,Ford VCM2, Toyota Mini VCI, VAG COM cable, Autocom DS150e, etc
I there any solution to get work my version of Xentry on older cars?
version 0.1071a (from 11/21/24)
— Fixed bugs that caused the program to freeze when connecting to blocks
— Added information about the current voltage on the device when connected
— New module [GM IPC]: Replacement of mileage, VIN and configuration coding
— New module [GM ECM]: Replacing VIN in engine control units
I need a solution of immo for PPD1.1 if is posible.
From time to time the car does not start. Random.
The only error is ecu blocked by immobilizer.
It has already installed an emulator from a few years ago for the steering wheel lock.
Probably the dashboard is having random problems.
So I would try an immo solution if there was one. For a fee, of course.
Could someone share Texa Truck (IDC4)version 37/38/38 and Texa Truck (IDC5)version 40.
After installing version v36 it throws error 49 which says that the installed version is older than the one unlocked on the HASP key.
Thanks in advance.
Hello guys, i need some help with calculate checksum at Simos 9.1. I have read from china kess and mod file with o2 off. Im a little bit affraid about make write without calculate checksum in different software before. (lsuite doesnt work)
Thanks in advance, best regards.
Hi to All
I need a bit off help fixing my problem on SDD JLR no internet connetcion , cannot download automated files
I do attach Photo whit problem pointed if you now how to resolve please let me now will pay you for your time
Using OEM VCI DoIP connecting to car no problem diagnose no problem .
Hi mates. Audi A6 C7 2016year. The car was factory-equipped with D5S headlights. Made retrofit to FullLed (not Matrix) 4G0941033H, 4G0941034H. The car was factory-equipped with a camera module in the window 4H0907217F address '85', without an HBA module address "20". Installation done according to Elsa diagrams. Installed and coded light module '55' - no errors. The camera module coding remained factory - no errors. BCM module 4H0907063GH, a dozen or so bytes have been changed, the headlights light up properly, low beam, high beam, position, DRL, turn signals. There was one problem, after turning on the ignition, the message "High beam assistant - system failure" appears on the dash, and an error is stored in the BCM module; 03455 - operation limitations due to the received fault value 000- -. There is no HBA installed in the car, there is a regular photochromatic mirror in the windscreen. in the camera module - HBA is not coded, in the BCM module - it is not coded either.
Or maybe every A6 C7 Lift with FullLed headlights must have the HBA module installed in the mirror????
Does anyone have complete Auto-Scans from the A6 C7 Lift, which was factory-equipped with FullLed headlights???
Maybe someone has at least the BCM module coding from a car with FullLed headlights??
Possible to find code from eeprom bin 95640 on this bosch radio used in iveco daily 2014
I dont have serial number but i have nr of model 7620 000 098
Daily my2014 ldws ext mic
Good day. I need to replace the dashboard of an Audi A3 and I got another one with the same reference number, numbers and letter.
Just copying the information from the 93C86 eeprom will copy the immo and km data, should I do something else? Or maybe just re-solder the eeprom? How do I replace it?
I been suffering for the lat 6-7 months, i have s560 w222. however i converted to s63 along with ECU AMG coding, and for the cpc.
when i turn on the car, after sometime it will show a yellow msg to add a quarter of oil, after it apears by short time it followed by a red warning "Oil lvl stop engine" i checked all sensors they are perfect.
to be sure that is coding problem. the Fuel range calculation isn't accuarate, my car fully tank goes up to max 800km. now it shows above 3,000km.
I need an expert to look into this matter please, job will be paid. no free things. to make it easier i got all tools, openport and DTS Monaco alrdy installed, just remotely check it.
is there any possibility to crack DTS9.04 like the 9.02 version? Ive got new Monaco projects, but with 9.02 it isnt working. I need 9.04. i have the Install Package for 9.04.
![[Image: a6AxvbH8vJ51fCkTZx2TWuL_K4E-1920.jpg]](https://a.d-cd.net/a6AxvbH8vJ51fCkTZx2TWuL_K4E-1920.jpg)
![[Image: N8WN0tRo3UHZVL8_SBUvjwHcWl4-1920.jpg]](https://a.d-cd.net/N8WN0tRo3UHZVL8_SBUvjwHcWl4-1920.jpg)
