Could someone help me to stage 1, egr off, swirlflaps off for my 3.0d M57 X5 173kw? I think previous owner already deleted the DPF (cat still might be there).
Hello, I have installed Xentry passthru on my laptop and everything is working fine exept for the startkey. When I first generated the key, it was valid for only a month or so. Now whenever I want to generate a new one, it won't go past the 10/25/2024 date.
Has anyone had this problem? And does anyone know how to fix it?
Hello, I found a diagnostic device for Merlo for sale, I wanted to ask you if it's worth buying?
What does this device do, are all the elements included?
Not many people have such a device, no one in my environment uses it. Do you have instructions for this device?
I made an adaptation through xentry, but after that I don’t know where to write the numbers, I don’t know which numbers to write, if you write straight numbers, then after that the car doesn’t stand straight
Hello, I need help with adapting the trunk of a w213 and I need to rewrite 2 blind spot blocks, who can help?The trunk closes, but the electric drive does not open completely, it only opens the lock, and the blind spot blocks, replacements from other cars, need to be flashed,[font=Roboto, "Helvetica Neue", Arial, sans-serif]It is possible to connect to the car online[/font]
Hello everyone,
i am looking for sp daten v40, i need them to restore a champ2,i have v39 and v41, but i need v40.
If someone has them please pm me. Many thanks
Hello, I need a good solution for BMW E61 535D 272Km M57. The controller is EDC16C35. I need DPF OFF, EGR OFF, Flaps OFF, CAT OFF and STAGE1. I already had several solutions, none of them were good, the car smoked at idle and reported an air flow error. Is there anyone here who can repair it properly?
I have a volvo s40 1.6d D4164T (EDC16C34) engine car. I have some dtc codes at original file given below. I tried to off dpf and egr system three times with different files but not successful. Car run into limp mode without dtcs with these dpf egr off files but not rev above 3000 rpm. Can someone have correct file for this car please?
I changed;
Mass air flow
4 heating elements
Oil pressure sensor
Fuel filter
Turbo replacement
N75 Pierburg
Pipes and hoses
Smoke test
Dtc's at original file;
Ecm 7700 engine control unit ecu
Ecm 9190 inler control valve
Ecm 9130 inlet control valve
Ecm 9140 inlet control valve
Ecm 2A10 particulate filter trap
Ecm 4477 egr control
Ecm 4460 egr control
When i delete these dtcs car runs perfectly short time. The origan file is given attach. Thanks for replies.
I have a k-tag, But new to the jeep platform. Any advise on this one would be great. I know about HP Tuners but I would like to be able to repeat the process with other PCMs as i have recently started working at a Jeep wreckers and will be helpful with cars that dont have keys from auction.
Can CONSULT 3 Plug be used to backup the existing ROMS/Firmware *before* you flash it with a new version???
I have a V12 clone, and I can get consult to save current config of the modules when doing a reflash and also when you are doing a blank program, but the files it saves don't seem big enough to be the actual backup of the firmware.
I am doing this in the programming/reprogramming section, rather than the maintenance section (which doesn't even detect the ECU).
Maybe they are saving them in a location I am unware of, but ultimately trying to confirm if I can consult does a backup just in case the programming fails and you have to revert back.
Two use case scenarios:
-Testing newer firmware on modules, so you can roll forward/backwards
-Backing up an existing firmware for programming onto a blank new module offline.
The v8.x version seems to be the last of the offline version, but the newer v2xx run offline now also. But are the actually different in functionality or more module support??
I have various Pplus version, which is the backend vehicle database, which comes up as "Programming Data Version", but the "ReProgramming Data Version" seems to be blank.
Not sure if this makes a difference.
Anyone happen to know why it seems if you reboot while the mongoose is connected to your laptop and launch JLR SDD it shows up as connected. If you close the program and restart JLR SDD mongoose seems to have a hard time connecting the second time or takes forever? Shows a message the gateway device is disconnected.
I purchased two Autel Xlink devices online to program a vehicle remotely.
One is intended to connect to the vehicle, and the other to the equipment. However, it seems that the Autofix platform requires professional certification to use the service.
It appears that this service is available in Europe, China, and North America. Is there anyone who knows if it can be used in other regions?
I have applied for the professional certification, but I haven't received a response from Autel.
If anyone has experience using the Xlink, I would appreciate your advice.
Hello everyone, need help. After storm my dart(2013 2.0 a/t) was flooded(salt water). BCM, Gearshifter ecu, climat ecu and airbag ecu are dead. I am fix all conectors problems and change damaged ecu (exept climate, it is unconnected now) . All ecu from same car, same year. I have problem with changing VIN number of BCM ecu. I have Thinkdiag (launch clone) and obdlink mx+ with alphaobd software. I try to copy pin at first from RF HUB(key socket) to BCM. Seems like it was sucess. But changing vin inside bcm failed. Any ecu have "configuration missmach" error. When i try make proxy, i have misstakes in ABS module, other is ok. How to configure my car in this situation?
Proxy from my new bcm in atachment( it is not my original one, unable to get original)
Can Xentry program the mirrors on a 2019 sprinter? I currently have the xentry and would like to know if programming and or coding the folding mirrors can work with it. I tried doing it with autel but it would not allow me to do so.
![[Image: JRws52Y.png]](https://i.imgur.com/JRws52Y.png)
![[Image: j.jpg]](https://i.ibb.co/2NPnc7C/j.jpg)
![[Image: aston.jpg]](https://i.ibb.co/2Sm5PLh/aston.jpg)
