"Hello, I am requesting advice from the experts. I have a W212 with EZS (A218 900 3501), it is FBS4. Can I transfer the MCU? By desoldering and soldering it onto the donor? Or is there anything else I should consider? Thank you."
Hello,
i want change ecu in Ford Transit DPC-635 cause car ecu dont have communication.
Ecu have MCU 600200FLC003 and AB28F200.
Can I clone this ECU? or can adapt donor ecu on the car?
We started chasing a few problems. We have a subscription to ODIS and ERWIN, but they won't let us sign up for ELSA PRO, and we are stuck switching the ignition key from type 1 to type 2 in ODIS until we get the SVM. Is there anyone here who can help with that? We are Robison Service, an independent shop working on Bentley in Massachusetts, USA.
The radio unit it this car will not come on with the key on - only when the engine starts. When shutting down, we hear a pop a few seconds after key is turned off. Having trouble confirming the dash unit as the culprit, and they are $10k in the USA, so concerned about that.
Welcome help from anyone experienced in these systems.
Hello all! I recently installed a BMW F90 Steering Wheel in my Supra J29 but am having issues with the ACC distance setters and the SET button. Also getting an error when hitting the RES/CNCL button. (Driving Assistance Support Reduced) All other buttons work as normal. Is there any coding that would fix this issue? Any insight would be greatly appreciated! Below is a picture of the steering wheel
I am having trouble with trying to program a new master key for a 2002 Toyota Camry. I have Xtool auto pro pad 2, Autel KM100, Xhorse Key tool max, all programmers complete program procedures but keys do not work. Engine just crank no start. I did notice that the security light on the dash by the A/C controls does not blink at all, not when insert key in ignition or anything it literally does not blink.
The vehicle was working just fine, customer lost his key and now can’t program new one. Please someone help me. I did find an aftermarket alarm system which I’m going to remove and reconnect the spliced wires.
Can anyone reccomend the cirrect inpa lead/interface. I initially want it for coding and diag on a 2013 e90 with n43 engine so whatever lead and software version that would work with that would be a good start.
has any one got the latest sdd to fully work with patch it downloads files ok and will update cjb but wont update the kvm errors out do i need a later update foe sdd or will this function not work offline mode
I need your help. I have an Octavia 2 RS common rail 2010 CEGA engine code. A while ago, my DSG transmission broke down. I replaced the transmission, but with a different code from the VW Passat. Everything is fine, the speed was very smooth. But the gearbox supported sailing. Because of this, every time I exceed the speed of 20 km/h and let off the gas, the transmission switches to manual. I wanted to eliminate it somehow, so I adjusted the clutch and adjusted the gear tolerance. The sailing was not removed, but the gearbox started to jerk. Can I get it back somehow? Does anyone know how to turn off the sailing mod? Can I flash other software than it is now?
Hello. I am urgently looking for a full dump for DSG DQ381 0GC300044E_2403. I downloaded the original dump to the car and after adjusting the mileage I uploaded it to the car. It says EEPROM memory error. When I put the original back in there it does the same thing. Probably my flash or eeprom memory was damaged. I read on some forum that they had the same problem with Gallet, they solved it with a second dump and customization via ODIS.
Hello, i have a Skoda Fabia 1.2 tsi 2014. Stock it has only 86 hp but stage 1 right now it should have about 120-130 hp. But ofcourse its very slow right now and i wanna invest in it abit. Ive had a downpipe and stage 2 tune and it was abit faster but still not happy(had to take it off cuz i had straight pipe and it was very annyoing in the cabin also police...). Does anyone know if i can fit a diesel turbo in it like a 22/60 and how much hp capacity does the intercooler have?
Hi,
Does someone have any infos about this ECU ? I’m looking for any damos or mappack to provide stage 1 or flexfuel conversion.
I can provide a read of a 2024 Arkana.
Engine is 1.6 e-tech 145hp hybrid.
Hello.
Fiat Ducato 2.3, after removing EGR and DPF with the DaVinci program, error P1206 appeared, which cannot be cleared, and the car lacks full power.
Before reading the map, I performed an oil change and replaced the DPF.
The plug from the differential pressure sensor is disconnected.
Did the program create a bad file? Can someone help me do it correctly?
Attached are the original file and the modified one.
ECU: HW: MJ8F3HW00D k
SW 1942B140
Replacement: 55246596
[font="MHH Font", Calibri, sans-serif][font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]Hi All, I've just done a oil and filter change on my Fiat Punto grande 1.2 petrol 2007 but now it's not starting all the lights are on padlock light goes out, but when i turn the key there is no cranking or clicking just silent.I've checked the fuses relays which tested ok, earth strap and even put a jump lead from the battery negative to the engine but still wont crank, i scanned with autocom and no codes were present any ideas. (it drove up my car ramps ok to do the oil change) car will bump start[/font][/font]
[font="MHH Font", Calibri, sans-serif]I have a 2012 vw golf 6 gtd and due to a battery replacement my radio rns 510 went out of order for some reason . Now it only boots until welcome to vw logo and restarts. I have been told I need to update my firmware version to fix it. But this is korean car so my questions is: can I simply download fw version for this radio type and radio code or are there more steps involved? I do not care about gps or anything like that only for my radio and bluetooth to work on it. I hope you can help with this question.[/font]
![[Image: comand-ntg55.jpg]](https://naviteam.eu/wp-content/uploads/2019/05/comand-ntg55.jpg)
