Have CAN-AM Outlander 600ccm, MY2017 ECU Continental M3C
Speed limiter 45km/h, registration certificate have limited power 14.4kw, but I think it is because speed limit.
Can someone switch it off??
Hi,
I have searched on Forum but find nothing related for my Problem.
I have x431 Pros Mini 3.0 Device without subscription. Im looking for third party Software for this
device to work with IMMO Programmer XPROG3 and Key Programmer, but i dont know what is the best Software for that.
Is someone with expirience on Forum with IMMO Programming options on Launch devices with other software?
I have PAD7 Elite too, but immo Software is to expensive (400€) for 4-5 times Programming .
My diagnostic Device is DS301 with serial 989520005595. Is it possible to work with this and what is the best Software for this?
Maybe someone can guide me or can recommend a good source?
Thanks
hi, I cant get a read from the cars original zf module, it must be completely dead, could someone please modify the donor file for me or have a virgin file so i can program it to the car.
ZF0501220441
CEJ32-14C336-AA
ES11-1023
I have Peugeot Partner Tepee (i think it does not matter) with central locking but without remote from factory. I was change Variant coding in BSI: Remote control from Missing to Present and program new key.
All work fine but i have one strange problem. After cca 5 min. i think car go to sleeping or Eco (i hear some relay in BSI) and remote control no longer work. Any react from car by pressing any button on remote. But when i do awake car, for example by opening door with mechanical key, remote control begin work again.
I guess need some changes in BSI to make remote control function change to Always On, but i not found any settings.
Hello, i have golf 6 2.0 tdi i replaced the mecatronic . The old one was 02e927770aj ( not really sure because i got the car with old mecatronic already in trunk. The new is 02e927770ad . Can somebody tells what flash file i should use for it.
VIN is WVWZZZ1KZ9W509012
I recently installed XDOS_24.3.4 on my laptop and , am using the C4 Doip , the challenge am facing now is I cannot find the SDconnect option
on the Config assist application ,its showing the vci option , and the simulation option only can some please assist me Iam new to this automotive world thanks in advance
Hello there, i have a 2023 audi a3 us spec that is not charging after a crash. Im getting this dtc p108f00, preload faulty. Any idea on what this is, or where is it located
Hi guys. I changed the Golf cluster , to an blue / red Tiguan cluster.
i addapted the immo , but don't have handbrake , i saw on some diagrams , that writes on PIN6 Handbrake signal (reversed in Tiguan vs Golf) , and the fuel level isn't right , and i have an error from level 2 sender , wich i don;t have on Golf.
There is a eeprom modify ? or how to set the instruments that are for Golf not for Tiguan ?
I wrote even the VIN of the Golf in the instruments.
can i find sameone who can make good solution to remove DPF, SCR AND DTC i tried many time to remove them but doesn't work so i wanna just good solution .
thanks
as already mentioned above I am looking for a programmer who could make 2 files for me. Of course not for free.
I am installing the 1.8T AGU in a UTV. This is road legal. But because I got a requirement for the registration of the engine in the papers of the vehicle I have to throttle the engine to 100hp for the “appraisal” of the engineer.
Two concerns:
- Can someone make me a 100hp file? (Original it has 150hp) Of course the engine won't run nicely, but I don't care because it will get a Stage 2 afterwards anyway.
- Can someone make me a Stage 2 with a hardcut limiter? Please do NOT add a pop/bang (recirculation valve), it's just annoying. Only Stage 2 with hardcut limiter.
possibly important info: I got the Ori files here from the forum!
Maybe someone can compare the two. They should actually be exactly the same!
I can only write and not read with the MPPS. But it matches exactly with the number 06a906018AQ
If someone wants to have something for it, please send me a PM.
i hope i can find a help here i'm new here maybe my post is not in the right place, i would like if someone can post here the shop manual or electric diagram for Honda CRV 2016 gasoline and thanks in advance.
I hade some dpf issues in the past and exchanged it 2 days ago. It seems that the issue laid somewhere else because I have now engine light and 400% filling level.
How can I force regen? Xentry does not allow above 200% to execute guided regen during a ride.
I can also not tell ECU that there is a new dpf in now and the fault code repeats immediately after deleting.
Can anyone help with a hint?
Thanks in advance
