Hello! I need help from a petrol tuner with this skoda. It has a stage that i read from the car, i think the afr is too lean in the upper rpm's. Also the missfire is off i think as there is injector problems and with the stock file the missfire appeared. Can someone help me sort this file with the tuning part and make it missfire on ? Thank you!
1037186859
0261s02339
1z0907115a
Hi, i have a problem after remap my ME7.5 ECU, after stage 1 ,my ecu just die. Can i get any advice how to fix this? when i trying to write original software i have info |invalid key" in my mpps app i think she need boot mode (can i do this on the car?) and put original software but i want to ask more proffessional lads. Thanks
Hi;
I use Clip v234 with token and my vci is SM2 PRO.Connection and without problem but when i try to connect car like new ZOE and logan i get this error "operation failed, reason : ecu communication
the gateway security level does not change.
if there is sgw in the vehicle, I unlock the vehicle from the unlock module before the clip, but when I open the clip, the process is not successful. what can I do about this?
Hi i,d try to read a sid 321 ecu with flex,but suddently the aplication is closed and when i restart the ecu is in program mode and the only option i can choose is recovery but i dont have any read.This is a screenshot after restart the program. Anybody can help me with a virtual read to restore the ecu? thanks
Good afternoon people, could someone help me create dsg farts on Vw jett gli 2.0tsi gen3 simos 18.2? dq250.... I understand that they are generated from the ECU. I would like it to have farts in all modes (D, S and TT) Thanks in advance!
WDD2211281A124817
Ori TCU 0335457332
Ori EHS 2202701906
Donor TCU 0335457332
Donor EHS 2202701906
SOFTWARE VERSION donor 0064488410
snc yb65
with this encoding and software the box twitches and switches incorrectly
It had a faulty conductor plate as there was no can bus communication in the TCU
Can anyone help me with the correct coding and software of the donor TCU.
Does anyone have a eeprom dump from Opel Astra (H) Simtec 71.6?
I have one with corrupt eeprom, been trying to read with carprog without success.
I found a video on youtube of a guy using KESS to make recovery of a Simtec 71.6, but that requires a working dump of the eeprom.
With the installation you fully activate Scania SDP3 2.62.1 truck/bus and marine/industrial AND SERTİFİCAS have both versions.
Cost:
SDP3 2.62.1 for - $60
.
sertifica 12 2024 - $70
.
Scania Multi 2024.05 for - $60
.
Installation on PC: TeamViewer/Anydesk
PAYPAL:
2.62.1
Update: 09.2024
Size Installed: 10GB
Region: All regions
Scania Scania Diagnos & Programmer 3 available in these languages: English, German, Spanish, French, Japanese, Dutch, Polish, Portuguese, Swedish, Norwegian, Suomi, Turkish, Italian, Czech, Russian, Chinese.
Scania SDP3 2.62.1 fully compatible with VCI3 and works only on Windows 7 and later versions including Windows 10 / 11 (64bit support)!
with 1 time installation service of Scania SDP3 2.62.1 Diagnosis & Programming for VCI 3 VCI3 without Dongle, this is the latest version Scania Diagnosis & Programming Software, working with Scania VCI3.
After the payment, please offer the Teamviewer ID and Password, Our engineer will help you install the software.
Scania SDP3 Software Function List:
Check and adjustments
Conversion
Maintenance
Campaign
Bodywork
Fault Codes
Fault Reporting
Programming of Control units
Scania SDP Installation Requirement:
Support Win7 64 bit system.WIN 10 32bit WIN10 64 bit (Tested by individual, so try on your own risk).
Need Netframework 4.5 installed on system. windows 7 or 8 will be better.
In order to install SDP3, administrator rights are required.
Note: The USB key and VCI must not be connected to the computer during the installation of SD
Hi guys, looking for somw direction here as this is one engine that tests my patience lol. Ok so engine runs but shakes at idle with misfire. Launch points to cylinder 3 misfire. Coils swapped...misfire comes back on cylinder 3. Spark plugs changed..no change.
Injectors removed and hooked up external on the rail and found 2 to be leaking, one not shutting off and another dripping. Replaced injectors and coded in. Still having misfire issues. Checked compression, figueres were high, Replaced lambda and nox sensor as faults were present, reset adaptions and the car ran fine for a day then its back to misfire issues and car shaking again. Considering buying the proper bmw diag setup as id love to get a better view of what's going on here.
Any ideas? Oh the timing chain was apparently done a year ago and fuel pump.
Thanks guys
Hi
I'm looking informaton how to convert to EU firmware in MIB 2 HIGH IN AUDI RS5 2019 year.
My software number is below im photo.
Somebody have a correct firmware in EU version to my MIB2 with Polish language?
I pay for solution
Thanks for advance
MEDC17 mileage tool - utility for changing mileage in eeproms of Bosch ECUs: EDC17, MED17, MEDC17, ME17, MEV17, MEVD17.
All listed ECU families are supported, regardless of the car manufacturer.
Tool works with eeprom files, supported filesize: 32, 64, 96,128, 192 and 256 kb.
ECUs with eeprom emulated in flash is not supported.
Simplified algorithm for using the program:
1. With the help of diagnostic tools, find out what mileage is stored in your ECU
(general mileage, last DPF regeneration mileage, oil insp. mileage etc.)
2. After eeprom opened utility analyze it and can show you all potential mileage stored in eeprom.
Your task as a user is to narrow down the results to be displayed using the available options and
find your mileage.
3. Replace mileage found in eeprom with the one you need (program will do it for you).
Save eeprom. Calculation of checksums is supported!
------------------------------------------------------------------------------------------------------------------------
Some car manufacturers store mileage in kilometers, some in meters, some in kilometers and meters at the same time.
The display of the potential mileage is supported both in kilometers and in meters.
-- all found values in the range 1 - 999.999 are considered as potential mileage in kilometers.
-- all found values in the range 1.000.000 - 999.999.999 are considered as potential mileage in meters.
-------------------------------------------------------------------------------------------------------------------------
Like any other program, this one has its advantages and disadvantages.
Advantages:
-- tool is universal and will work with all eeproms from the listed ECUs, regardless of the car manufacturer
-- program will show potential mileage stored in eeprom
-- you save a lot of time working with the file (no need manually search for mileage and edit eeprom)
-- automatic checksums calculation
Disadvantages:
-- this tool is not a magic wand and will not do everything for you automatically in two mouse clicks.
The vast majority of values found in eeprom are NOT mileage! It's very easy to change the wrong values
and end up with a damaged/non-working eeprom. So, some brains is needed!
-- do not try to use this program as a checksum calculator!
Checksums are calculated only in those eeprom blocks in which program made changes!
-- if you just want to know mileage stored in eeprom without having any other information - this tool will not help you.
Screenshots:
Example of using the program (Youtube):
1. Renault Captur EDC17C84 eeprom (mileage stored in kilometers) https://youtu.be/i2WOKTpEnqc
Hello,
does anyone know what coding there is for the block?
Address 51: Electric drive (J841)
Part number SW: 5G0 907 080 x HW: 5G0 907 080 x
or
Part No SW: 0EF 907 080 F HW: 0EF 907 080 F
So far I have only found 2 possible codings:
1st coding: C00200000000000000000
2nd coding: 010000000000000000000
VCDS doesn't show anything, VAS PC ODIS 12 doesn't have any information for it either.
Thanks
I need help with bricked ecu dcm3.5. Other garage broke ecu by write mod by OBD. I found full dump from other ecu and wrote by jtag. Ecu is alive now but I need to program immo. I read BSI dump and try find pin code and probably it is TRMK or RMKM but bsi not accepts it. Additionally I need make virgin ecu for adapt immo.
Car is Peugeot 407 2009 2.0HDI RHH.
![[Image: m5OxDV.png]](https://r.resimlink.com/m5OxDV.png)
![[Image: qjRubXUz.jpg]](https://r.resimlink.com/qjRubXUz.jpg)
![[Image: 1.jpg]](https://i.postimg.cc/kBM6jk8J/1.jpg)
![[Image: 2.jpg]](https://i.postimg.cc/6TWpwCQz/2.jpg)
![[Image: 3.jpg]](https://i.postimg.cc/4mn4HZV9/3.jpg)
![[Image: 4.jpg]](https://i.postimg.cc/23SrgmHK/4.jpg)
![[Image: 5.png]](https://i.postimg.cc/7bFDZYTk/5.png)
