Which key programmer is better in terms of functions: the Launch or VVDI MINI KEY TOOL or VVDI Key Tool MAX or what do you think? I can't manage my key prgramer from launch.Thx all
I have a Daf 106 with a MX-13, and i'm getting red light and the code P0094, already tried to run engine without one pump disconnected, its unsseseful, the engine wont run either one, but with the 2 runs.
Secont attemp, the wihte ball was been changed for a new on(not necessary i know, stuck on open position btw), changed all the filter, and changed the 2 units, now after a run on the road did the same.
On first attemp showed the P228D, but disapeared after filter change.
Hi everyone im doing MSD80 to MSD81 converison, VVDI2 wont replace ISN in ecu, can someone please do it for me Bellow is MSD81 backup read with AT and ISN from original MSD80 is bellow Thanks and best regard, rep and thanks will be given
Bonjour, je dois mettre à jour une Audi R8 de 2016 pour utiliser CarPlay. Je connais bien la méthode car j'ai une TT MK3. Mon problème concerne les fichiers à installer. Je n'ai aucun problème avec la partie MMI. En revanche, je ne sais pas quel firmware installer dans le Virtual Cockpit. Celui de la R8 est le 4S0920790, alors que le seul firmware que je trouve en ligne est le 4S0920890. Est-il compatible ? Ou existe-t-il un autre firmware à appliquer ? Apparemment, l'opération est réalisable, car plusieurs spécialistes le proposent. Merci pour votre aide.
Hey everyone,
I’ve been struggling with a cluster (tachometer) swap on my Polo 9N, which uses a Simos 9.1 ECU. After multiple attempts to get everything working correctly, I’m looking for a reliable IMMO off solution.
I’ve attached my ECU read file in the hope that someone here can help me remove or disable the immobilizer. The cluster replacement has caused a lot of headaches, and I’d really appreciate any advice or assistance on how to make this work smoothly.
If anyone has experience with Simos 9.1 or has done something similar on a Polo 9N before, please let me know. Any recommendations, software tools, or even direct file modifications to get IMMO off would be incredibly helpful.
Thanks in advance for your support!
Best regards,
hi i have a hex v2 cable from ali express so its from china what software i can use for EDC15 and EDC16
i have vag can commander
i have dash dumper
i have vag programmer
vcds 20.4.2
all these software work withe same hex v2
[color=var(--YLNNHc)]Hi, I have an android device for a BMW X6 2010 E71. After the customer has put their car on charge, the Car Play android device does not work. I can see that a component has burned out on the circuit board. If I'm lucky, maybe it will be enough to replace that part. It was apparently bought in China via aliexpress. Is there a possibility that there is someone who has one lying around and can check what is written on the circuit that has burned out. The position on the circuit board is Q21. The model of the device is. (CT-032L-32G-2G-V1.3B).
It looks like that part has to do with the power supply. I'll send you some pictures of the board and the burned component. Best regards, Ronny.[/color]
Hi friends, I have a second hand Opel E87 ecu and I need to match it with the immo system of the Corsa D 2010.
OPEL CORSA D 2010 with A17DTS engine.
First of all, I tried to clone it but the faults from the original ecu were transferred to the second hand ecu, so I think the best way is to do a reset and after that I will try to marry it with the immo system.
Attached is the file I read kess3 by boot mode. I think the pin is 7048, could someone check it?
Opcom has no options in its menu to do the reset, and I'm not sure if I can pair it with the immobilizer system.
Fvdi, it doesn't reset it.
Im608 does not reset it.
Opcom 2022 does not have the reset option in its menu for this ecu.
IOprog does not identify the pin correctly.
Could anyone support me with some information on the way with this ecu?
im having issues with the car not really reading my disc or having issues with my CFF. It starts the update goes to 0% reading up to about 12 seconds then goes flash broken off. In this time the radio screen goes blank and then goes back on im guessing its my DVD that is wrong. im using ImgBurn at speed x1 verbatim DVD-R 4.7 GB ive also tried Fujifilm DVD+R no difference
Hello,
My Launch X431 key programmer dongle is stuck in blinking blue light (flashing mode), cannot update firmware and cannot get it out of this flashing mode. Anyone have any suggestions how to get it back to solid blue normal mode. Please let me know if there is a software to reflash the firmware or fix this.
hi guys in new and amateur on this lol
i have a PD TDI ATD 100 HP ecu and i injected a file [ i use mpps v18] from another ecu but not PD TDI its an ASV TDI 110 HP and now i cant read the ecu how can i repair it and whats the softwar thank you
Bellow is MSD81 backup read with AT and ISN from original MSD80 is bellow 
