Hi.
Please! I need your help to reset km from EZS, i recently buy a W639 Viano with 1.166.000km more or less, odometer stops in 999.999km.
Need to reset to 0km to pass circulation vehicle inspection.
Who is able to reset the flash counter on an EDC17CP44? This is a post emissions scandal ECU so the flash counter should be reset to 1.
Currently the ECU is OBD locked at 51 flashes.
Hi,
I need scr and dpf off here, vehicle is Bucher but egine iveco eurocargo, Its with vario transmission and when all okay goes 50kmh but now when in limp mode. only 10kmh.
Swiftec, davinci solution dont work
I tried many solutions for this vehicle but no success, buty everyone says solution is tested When I laod file all okay and vehicle goes okay but after next start in limp mode and only 10kmh
hi at all, i havve a mini cooper mev17.2.2 with solution immo off , but i have need calculatin of checksum correction because the car start 3 times and no anymore.
Hi all.
I am facing an issue with a W204 with 272 engine ME97.
The car wont start dash lights on no crank, jump the starter it will start at time some time it will just crank but nothing.
Randomly it start from the first go with the key.
On scan no fault code except communication with alternator/starter.
Read data from ecu with Autel IM608, back up coding virginizes a used ECU, load the data install to car but impossible to teach drive authorization. Check DAS live data all N/A.
ECU back to the bench and no communication cannot be renewed.
Original ECU same issue cannot be renewed.
Open the original ECU found that some wizard did a witchcraft that i dont understand on it picture attached.
Any one has an i dea on how i can tackle this issue?
Thank you all
Services they have - they works - we used quite few. But in particular Odis parameterization files is crap - we did out of curiosity test paying and pulling out gateway file - and to our surprise file was manually stripped removing few sections - example FPA. In attempt to report issue on telegram(official way they have) - no response(middle finger approach it seems..)
Take above not as a crap spilling on supplier but more as reason for careful consideration - to pull parameterization files for odis ideally you require live car and online odis - rest is more based on already saved/altered files by someone with no guarantee file is correct and safe. Yes there alternatives as VCP - but that is not subject in this post.
Recently, 4 users Paneito, aemtuning, skunk, and zdsSF left me negative feedback on the same day, almost at the same time. This clearly looks like a coordinated attack rather than coincidence.
What’s more strange any honest negative feedback left for Paneito, aemtuning, skunk, or zdsSF disappears shortly after, like it never existed. This gives the impression these users are somehow protected by privileged members.
Personally, I am not worried about feedback my work speaks for itself. But it’s important for other genuine users to know what’s going on.
Honestly, I won’t be surprised if this thread also gets removed or locked for comments... that would just prove my point even further.
Anyone else had similar issues with Paneito, aemtuning, skunk, or zdsSF? Feel free to share.
Hello everyone, I'm having trouble reading an edc16c34 from a 2005 citroen c3 1.4hdi via obd. I can't find the correct protocol to read with kessv2 clone. Can someone suggest a solution? I apologize if I didn't post in the correct discussion. Thank you in advance.
Good day.
Can someone calculate the checksum for me?
My flasher can calculate, but I'm doing it remotely for a friend, his flasher won't calculate it.
Thank you.
Hi. I m looking for wiring diagram for RAV 4 2.0 DiD, year of production 2004.
I have issue with glow plugs (no power) and i check all fuses , all is ok. And relays work too.
Hello, I have a 1998 Mercedes W220 S-Class with automatic transmission errors related to the gear lever in the passenger compartment sometimes it stays in P sometimes it works. We found a used lever in a car scrapyard and installed it in the car but with this lever it always stays in P, is it perhaps necessary to adapt the lever? How? Can you kindly help me? Thanks
When I laod file all okay and vehicle goes okay but after next start in limp mode and only 10kmh
