hi need help ...
i have ecu from mercedes w211 2005 2.2l i need virgin eeprom to adop ecu to the car... i have bat battery and i lost authorization ..
A6461534179
0281011328
CR3.11
I need TESTED immo off file for Fiat Ducato 2.3, 2008, edc16c39, 0281015576. Car is stuck in another country. I have only the ecu. I have attached full read bdm files.
Hello, I have EIS from a Mercedes w212, after driving 12-15 km and turning it off, it does not see the key (terminal 15c), when it cools down everything returns to normal. I wanted to replace EIS with the number A2129055000, can I replace it with another number because I can't find anything with that number in my area.
Hello,
i got a 4G cluster where i messed up the CP bytes....
Luckily i still got a OBD Read with Abrites (SVCI2020), can someone tell me the CP Bytes from the dump?
With abrites i cannot open the file, nothing happends...
Berlingo 1998 without ECU.
Engine DW8 (WJZ) Diesel.
I have an Immo problem. Someone else has already worked on the vehicle. The EEPROM on the Immo box was poorly soldered, and the file wasn't correct. I need an Immo file for the vehicle. Does anyone have one? I copied one from YouTube for Peugout Benzin, but to no avail.
I would like to change some adaptation parameters in 09 module in 2024 Audi Q3. So now, I unlocked 19 gateway and unlocked 09 BCM module. But I still cannot change anything in Adaptation.
Is there any option for changes in 09? Why it is still locked despite the status is unlock.
Hello I have Opel Astra K 1.6cdti,
I have make dpf off, but after I drive car for while, There comes "Cleaning exhaust filter. You must continue driving" on dashboard!
No dtc on ECU, I also did make reset with diag on ori file, Dpf sensors are disconnected!
Hello guys does anybody knows how to replace correctly the sagem s3000 with a virgin ecu ?
I already transfered the immo chip from the old one, should I just write it the flash with kess ?
Ori attached
I am trying to instal Ista 4.52.40, but I am having so many issues, I am now totally lost.
The computer I am installing is Core i5-220MHZ, 8GB ram, 512GB SDD.
I created C:\SharedStorage folder, and copied all the install files there.
I installed Ispi Admin Client 24.4.11.
Then installed Launcher 1.51.10.16...
Rebooted.
Launched Launcher, and Finally, after maybe half a dozen attempts, it finally installed, but this took just over 12 hours! ( Loads of errors trying to "verify and repair" 4.52.40.msi APP.) However, when I started Ista, it opens up, but with the error that Ista 4.52.40 is not released yet, so the program cannot be used. When I click on 'OKAY', Ista just shutt down.
I have tried to figure out why I might get a message saying Ista-D 4.52.40 "is not released yet", but can find no answers. So, I deleted the instal, made a clean copy of Windows, and tried the installation, but now getting a different error. Now the error is "The SharedStorage location ('') is not accessible"
I put it on C:\Sharedstorage, D:\SharedStorage, E:\SharedStorage, and even though
I can see all the installation files there, Launcher never see's it. I have checked the MD5 Checksum of the files, and they are correct. This is on my Windows 10, 64-bit. However, when I try it on Windows 7, (64-bit), Launcher can see the correct path.
Can you please tell me which file in Admin Client I can change to point to correct path? I am using Admin Client 24.4.1130.359. I am really lost in the woods here, and I am desperate for your help.
![[Image: jMcKSo7.png]](https://i.imgur.com/jMcKSo7.png)
