Good day! Renault Megane ECU Bosch MD1CS006. Need to replace the ECU with a used one. Lots of information that replacement is only possible with a new one or disable the immobilizer! Could you help disable the immobilizer in this ECU?
Good morning everyone, does anyone know where I can find the developer of the XDECODER software?
bertus82 I have sent several emails and have not been successful. I have the original software so I don't have any problems, but I am trying to install the software and I can't.
THANK YOU
Hello
I wanted to connect to a Volkswagen Up. odis does not recognize it and it is not manually selectable.
the vin is read regularly, but the model is not recognized automatically. by selecting the volskwagen menu, all models come out except UP (aa)
hello
i remove o2 sensor and i try to remove lambda off /deacat but i dont see the P0420 code on this file .
any idea pls.? https://easyupload.io/updeho
Hi the C4 went bad after times use , can help me check out where problem ? Xentry software or Hardware IC ?
Communication error (4.?.?) :
Initialization of the multiplexer has failed.
Possible causes and remedies
Notes for support com.teradyne.ds.gradex.asam3d.Asam3dResourceBusyException: Error details:VCI is already in use at intern/GetBatteryVoltage/NODE18 in file:/C:/Program%20Files%20(x86)/Mercedes-Benz/Xentry/Kontexte/Allgemeine_Ablaeufe/Fahrzeug-Kommunikation/Asam.gmf
Can anyone clear crash and crash counter from cupra born 1EA959655ER VW40. Read with vvdi prog. Adding d-flash
Faults from module cannot be cleared with diagnostic.
Hi guys .Please someone help me repair the following BCM2 files from an Audi A4 B8,no ignition after wrong polarity by some guy.I put a donor BCM from another car and we got ignition to work.
need some dtc off on opel meriva a 2006 me7.6.2 read it with fgtech
dtc s that need to be deleted are
-p1113-4
-p0403-2
-p0443-2
-p0135-2
-p0141-2
-p0443-4
-p1113-2
-p0135-8
-p0141-8
-p0403-4
so all egr and the above ones
Dear Members! Could somebody help me? In our workshop there is a Scirocco with a broken 02E927770AJ unit. Bought an AL. Vin: WVWZZZ13Z9V017348 Could somebody tell me what is the correct sgo for this unit?
Hello everyone!
My customer recently bought this car and it came with a weird stage1 or some sort of tuning done to it, I need a ECO file with a lot less NM and a lot less power.
Here is the OBD readout and the id attached
If someone could help me out I would be super thankful!!
Driver:
VOLKSWAGEN
GOLF 4 -1J-
1.9 TDI EDC15P
1,9l R4 EDC
1024K FSUP
1037363166
0281010974
Flash:29F400BT
Hello, is anyone here selling enable codes for BMW motorcycles? I have the kit (part number: 23418536884), but after installation I will need FSC code to activate with ista or esys. VIN number is WB10M1105M6E42414
Hello, im working on adding key to G63 with w166 eis and 722.9 7G tcu. Key number 1 was disabled, i re-enabled it. I also added additional key. Both keys now turn ignition on, i can set gears while engine is off. If i start engine then i no longer can switch gears- drive authorisation on ISM is not active anymore (while active on IGN on, engine off)
Existing original key on track 2 can start the car and change gears and normaly drive. Issue is with additional keys.
Is it possible to sync tcu/ism with eis to fully activate previously deactivated key track or new key track?
Or the only solution is to virginize tcu and ism?
