I need to connect a central motor with ODIS. It is possible to use the GEKO accessory. The access is correct. When starting the control for the first time, the error FAZ2802E is not authorized.
Can someone give me some guidance?
I'm currently fighting an epic battle with a 2008 VW Polo dashboard (part number: 6Q0920823T), featuring a notorious Magneti Marelli unit with a stubborn Motorola MC9S12H256 MCU. This dashboard is proving to be tougher than my mother-in-law's Sunday roast!
Here's my story so far:
I tried using my trusty UPA-USB programmer to read the full flash dump (files attached). However, instead of the PIN I was expecting, I got...well...nothing. It seems the MCU is secured better than Fort Knox.
Desperate times call for desperate measures, so naturally, I went ahead and bought an Iprog+ programmer. Turns out, this fancy gadget is about as useful as a chocolate teapot. Money officially burned!
This dashboard has been haunting my dreams and draining my sanity. I'm desperately trying to get the PIN so I can code the new dashboard to the car—the old one has decided to retire early with multiple failures.
Could anyone here enlighten me or suggest a different method, or maybe even save me from further financial embarrassment?
I appreciate any help—my sanity (and wallet) will thank you immensely!
Hi guys I'm working on w118 2022. Have been replaced used ESP 117 control module and now i'm stuck at invalid vin number. I have looking onto Xentry and DTS Monaco but I didn't find a clue how to do it On xentry special function FIN cannot find good working password to reset/write. Is there anyone which can help with this.
Does anybody know what is the correct coding to change to remove the function for swirl flaps in ME9.7??? Swirl flaps not intake runners. I found in coding "ladungsbewegungsklappe" which translates to "charge movement flap". Thanks in advance.
Hi, does anyone know where to download the VDM Ucandas Wifi OBDII Automotive Scanner software? I installed the software and it doesn't connect to the official website. Apparently, it's disappeared. Thank you very much.
hola , alguien sabe donde descargar software Scanner Automotriz Vdm Ucandas Wifi Obdll , por que instalo el sofware y desde el mismo no conecta a la pagina oficial, aparentemente desaparecio. Desde ya muchas gracias
Hello everyone,
I need help with an Immo Off solution for an Audi A4 B8 (engine code CAHA) equipped with an EDC17CP14 ECU.
The ECU reference is 03L906022BL.
I have a full backup (EEPROM, Flash, and MPC) read using Flex.
The car doesn't start due to an active immobilizer. No fault codes are present, but IMMO is preventing engine start.
I'm looking for a safe and tested Immo Off solution – manual or modified file.
If anyone can help or provide a working solution, I’d be very grateful.
Thanks in advance for your support.
Best regards,
Yacine
car was showing 125,000 miles and i need 30,000. tachosoft reads file wildly wrong like 400,000 miles. i have paid for 2 corrections and neither are right. i have original files in 8 bit and 16 bit attached. not sure which one i should be using. if anyone could nhelp i would greatly appreciate it. eeprom is 93C66. well it wont let me attach .bin files.
Hi i need dpf and egr off for
volvo 1.6 d2
ecu denso
2015y
need tested solution
I tried several paid solutions with disconnected sensors and reset before saving, they do not work, information on the display always lights up about a full filter
if necessary I will pay again for good job
thanks
hello In general, this OM651 engine has DPF problems and risks leaking at any time,
so the best solution is to remove it with a very good solution.
thanks
I am looking for a full backup (EEPROM + FLASH) or clean EEPROM dump for ACC radar module:
VAG part number: 2Q0 907 572 B / G
Continental ARS410 / ARS4-B
MCU: Infineon TC1793
The original unit is not responding to VIN/UDS commands and I plan to recover it via BSL using PCMFlash + Module 53.
Clean or donor dump is fine — just need to revive the unit.
Any help would be truly appreciated.
I am looking for a full backup (EEPROM + FLASH) or clean EEPROM dump for ACC radar module:
VAG part number: 2Q0 907 572 B / G
Continental ARS410 / ARS4-B
MCU: Infineon TC1793
The original unit is not responding to VIN/UDS commands and I plan to recover it via BSL using PCMFlash + Module 53.
Clean or donor dump is fine — just need to revive the unit.
Any help would be truly appreciated.
I know this is an issue with the 9/2023 Xentry that the multiplexer doesnt get activated and you get an error like this:
com.teradyne.ds.gradex.asam3d.Asam3dHWException; Error details:VCI is not available; diagnosis plug possibly not connected at intern/prepareinterface%20-%20Task/NODE16
in file :/C :/Program%20Files%20(x86)/Mercedes-Benz/Xentry/Kontexte/Allgemeine_Ablaeute/Fahrzeug-Kommunikation/Asam.gmf
I have passthrough I have tested my multiplexer works. Anything over 2014 (newer Xentry where ignition box is embedded into Xentry) will do this but older car (older Xentry where you need separate program to set ignition on/off for passthrough) is always works.
I've seen black list fixes and whatnot, however am I supposed to install this with a fresh installation of Xentry or can I do it with the one I have now?
