Hello, could someone turn off the immo, I would be very grateful for help, the controller displays error P157000, the control unit is turned off, thank you for any help, I am uploading the eeprom and flash
The car:
VW Passat B8 2.0 BiTDI MY2015.
Story: Owner went shopping, came back and car did not start. Someone else tried to clone the ECU to a donor but i think the main problem is, he also cloned the corrupt eeprom. No Vin inside, only "EEPROM-READ-ERROR".
The Car had a lot of CANbus related faults so i changed the Gateway module to a used one and programmed it using ODIS online. Also did SVM on all other modules and all seems fine. No more CAN-Bus communication errors in any ECUs.
Still the ECU shows
"ECU locked" and "RAM Error"
which sounds to me like a checksum error.
ODIS Tells me, the ECU is not known to the cars immo system and thus i cant start the engine.
And because no VIN is detected inside the ECU i cant program the immo system using ODIS. It does not list the ecu under immo components.
Also tried reflashing ECU using ODIS-E but it does not allow me to, as the Immo is not ok.
EEPROMEDITOR from Neurosuite can not decrypt the EEproms, gives back an unknown error and cant decrypt them.
So: Does anyone have a working eeprom from this ECU or can repair my EEprom file?
SW: 03N906026E_2114
Partnumber from Sticker: 03N907309
Hi, good afternoon, I'm searching a full backup Int_eprom and Int_flash file by a Yanmar SV100 Excavator with bosch edc17cv54, 1R1797-00101 Engine 4TNV98CT I bought a new ecu witout program and original ecu was died.
I found some original Int flash files uploaded int this forum but I need also Int Eprom.
Hello, i need help with a tuned file for a bosch me 9.2 n42b18a with lambda off after(post) catalysators. In ecmtitanium it gives options only for spark and injection. Any help would be great. Thanks in advance. I attach the file in the archive.
Hello, another strange problem:| i have this CITROEN C3 1.1 year 2011, with remote problems.. remote is working only sometimes, but every time i hit remote button (open or close) SERVICE on dashboard goes on. Also i noticed that even if I put on my seat belt the light doesn't go off. ook, found pin, did a new key and SAME PROBLEM. Now i supposed something corrupted into bsi, so... TOKEN and updating using lexia online.. i could update the bsi flash BUT problem still there.. Read using IOTERMINAL full backup and found something strange into eep (iot cannot find the pincode) so i am pretty sure that even if i updated bsi , this error is still there into eep.
Anyone can repair my dump? i made a screen of psa references using iot and a full backup.
Please
OR If i find another dump compatible , can be changed PIN , VIN and MILEAGE to match my original one? thanks again
Im having trouble with the checksum calculation for a tuned file , can anyone help me fixing it , im willing to pay for the help , need it ASAP
The car starts and then die with any tuned file , but works perfect with ori file , im attaching the tuned file Im wanting to write and the original one for comparison with ecu ID
hello,
i need Unlock for GPEC2 (Jeep Wrangler 3.6) for HPTuners. Currently i can only read but can't write, can someone do unlock on the file so that i then can write via hptuners.
Attached Intflash and Inteeprom (read with flex boot)
I've done some searching, I'm ignorant and do not understand the nomenclature for Mercedes at all. Here's the situation:
I have a 2012 Sprinter 3500 with a OM642 3.0L diesel in my shop for repair.
I used a Texa Multihub TXT diagnostic scanner.
- Sprinter has 0 Starts remaining from a bad DEF tank level sensor and nox sensor issues. I replaced the nox sensors and DEF tank. I was able to clear the nox sensor codes, cannot clear tank code and none of the texa functions are working to increase the number of starts.
- I can't get an appointment for 2 weeks to get this vehicle to mercedes for them to just scan it and clear codes.
- I want to get XENTRY myself (found links here). Problem is I have NO IDEA which XENTRY will work with my TXT multihub, nor do I understand the nomenclature for what I need to download. I do not understand all of the different versions and acronyms for xentry, nor do I know what I need to scan and clear codes on this sprinter.
Any help is appreciated. Thank you.
![[Image: WZLZrm9.png]](https://i.imgur.com/WZLZrm9.png)