Hello everyone
I have a volvo s40 with esp lamp on.
I have the following fault code :
EPS-0080 Steering wheel angle sensor : faulty signal
If I check live data, the steering wheel angle actual value stays on 0 deg.
Can anyone guide me with what to begin to check?
I tried calibrating, launch says it was succesfull but same errors.
Thanks
Hello, with which tuning programmer can i read the ecu Toyota Hilux 2.4 110kw from 2017 with MCU processor D76F0219F1 2048Kb Gen2 excluded CAN BitBox Toyota Denso Gen2, which blocks the ECU when writing?
Hi all member I have problem with w211 E200 compressor engine jerky when engine hot I check all fault code have !when cold engine start fine all member have help please
Hi, I have corrupt eeprom in EDC16CP33 Nissan Qashqai
There are two dtcs after dpf reset:
P0611 Injectors faults (no coding)
P1612 Immo nats
Can somebody make virgin from my eep file or repair corrupt eep?
Thanks in advance
hi,I swapped a DSG DQ250 to DQ381, everything is ok.
except 2 problems
1.When change mode in the selector thee rpm jump to 1500rpm and go back idle
2.in neutral the speed rises to 4000 rpm
I think I need to change something in the file, but I don't know what. If anyone has already done this and can help me, please let me know.
Thanks.
Hi.
can I deactivate on my GLE 2024 the speed limit warning as shown in my attached picture? All the time I have to turn it off when I start the engine. I want to deactivate it permanently.
Is it possible with Xentry and VCX SE?
Leyland Daf 7.5 t mileage, only chip i can find on the board that makes sense is 24c32 current mileage is approx 362239 miles and it needs 352241 miles
can anyone confirm this is the chip with the mileage and amend the file for me? I will leave thanks and reply.
I have three PIWIS computers in my shop two are running 42.950.025 and one 43.300.00 One of the 42 and the 43 both close at the automatic model line detection screen when using diagnostics. If you click on manual model line selection it will allow you to go in. If you use diagnostics 38.250 it will run automatic model line detection fine. The other 42 runs automatic model line detection fine for Diagnostics. I cannot figure out why. Help?
Easter promo on winols database for only €550 paypal payments accepted goods and services payments accpted please pm for database listing all links provided via mega dowload
CARS/TRUCKS/AGRI/BOAT/BIKES
I’m currently looking for a professional tuner who is highly experienced with the Simos19.6 ECU and the EA888 Gen 4 engine. Ideally, someone who has previously completed successful Stage 3 projects—particularly with TTE575 or similar turbo setups.
This is not a learning opportunity or trial run. I'm looking for someone who already knows the platform inside out and has delivered solid, proven results in the past. I'm not interested in “I’m enthusiastic and I think I can do it” responses—only seasoned tuners, please.
I have no issue with paying for quality work. If you know what you're doing and have the experience to back it up, budget won't be a problem.
Please DM me or reply with your portfolio, reference projects, or any relevant info.
hello,
have rewrited 93C46W7 eeprom with wrong file and don't have good backup (when made km with dp4 made wrong chip choice)
Maybe someone have eeprom backup and can share. Car is Lexus 400h European version with screen where info and door open is showing (the biggest screen).
![[Image: 5f924307dc616496e3c8003d1a55b970.jpg]](https://uploads.tapatalk-cdn.com/20250419/5f924307dc616496e3c8003d1a55b970.jpg)
![[Image: c5a9ae9adf95711d2a6a326b827efb35.jpg]](https://uploads.tapatalk-cdn.com/20250419/c5a9ae9adf95711d2a6a326b827efb35.jpg)
(when made km with dp4 made wrong chip choice)