|
|
|
| Ford Transit MK7 dash repair and bench test. |
|
Posted by: Mulins - 04-21-2025, 11:57 PM - Forum: Automotive Airbag, Dash, ECU, IMMO.
- Replies (1)
|
 |
Hi to all. I have transit MK7 with no power on IC at all. After welding all around now It wakeup and didn't show mileage or hour. After removing +15 the retro illumination still remain on. I'm looking for a way to diagnose it on bench. Diagram shows it have 6 WAN (vehicle area network). Kindly someone know how to diagnose it?
I Have forscan, autocom ecc.
|
|
|
| W177 Navigation is not working |
|
Posted by: Mohammed370 - 04-21-2025, 11:52 PM - Forum: Daimler Group Mercedes-Benz, Smart Discussions.
- Replies (8)
|
|
Please help me with my A class 180 w177 2019, I bought car with front accident and the Navigation is not working, I'm getting this when I'm trying to open the maps(the map data does not match that on your system) and shows 2 errors:
-P164452 : An incorrect variant coding or configuration detected - component not in operation
- B154600 : The map data on the hard drive are not compatible with the current head unit software.
I have launch x431 and I can change the variant coding, but I don't know what exactly I have to change there are a lot of parameters
I contacted the previous owner, he told me they were trying to activate the AMG menu after that they lost the maps, how or where can I find the original variant coding
|
|
|
|
| Ista+ 4.39.20 Passthrue with Bosch KTS Problems |
|
Posted by: T-Modell - 04-21-2025, 10:21 PM - Forum: BMW Group BMW, Mini Discussions.
- No Replies
|
 |
Hello, can someone give me an idea to get ista+4.39.20 to work with Bosch KTS570? I have downloaded the current Bosch Passtrue driver, also Bmw PT Configurator it will also start the IHF, but it does not connect to the car. I copied the Bosch dll into Systemwow64. In PT Confiog I can select Bosch and in Ista I have selected Passtrue. Firmware and connection to the PC are ok, only use it via USB. I think it's wrong settings, because it's a standalone version here from the forum. The path for the PLsZ was also wrong and didn't want to work. Thanks for tips
|
|
|
|
| Flashing different Firmware on FORD Park Assist Module |
|
Posted by: gunnar1001 - 04-21-2025, 09:03 PM - Forum: Automotive Airbag, Dash, ECU, IMMO.
- Replies (1)
|
 |
Hello everyone. I have a Ford Fiesta MK8 with factory fitted rear park assist, the PAM (Park Assist Module) fitted is HU5T-15K866-AG, that is called Rear Parking Aid Module.
I'm currently retrofitting front parking sensors, that I've already bought and wired up.
Setting my current PAM with 12 Sensors and Front Park Aid: Enabled returns DTC for incorrect configuration.
The correct unit to fit would be HU5T-15K866-CH, Active Park Assist Module.
But looking at the two units they say on them "HW_04" and has dfferent SW_xx0xx. Both of them have the connector for the front pdc. Given those assumptions I think the unit is the same.... same hardware just different software, so in your opinion is it possible to flash to my PAM (-AG) the firmware for the -CH version?
Forscan for my current unit says:
PAM - Parking Aid Module
Part number: HU5T-15K866-AG
Calibration level: HU5T-15K866-AG
Strategy : HU5T-14C090-AG
|
|
|
|
| Ms45 Pedal Sensor |
|
Posted by: josef1708 - 04-21-2025, 08:38 PM - Forum: Automotive Tuning.
- No Replies
|
 |
I have n45 bmw 1.2004
I think me9.2
Always Gas Pedal Sensor 2 issues (dtc:2d1a,2d1c). Replaced wiring , ecu , Pedal and Everything but still coming up. Is there a way to deactive the Check for plausibility Sensor 1 and Sensor 2?
It goes into limp Mode and the Pedal is stricted to 30 percent.
BMW 116i 2004
|
|
|
|
|
