Hi guys. I have a Volvo truck that I've been able to read via OBD and apply the AdBlue solution. The funny thing is that now it won't do anything via OBD.
I read via Bench. Is it possible to disable the AdBlue system, please?
I'm adding an OBD reading with AdBlue disabled but unable to write.
And a boot mode reading in case anyone can apply the AdBlue off solution, please.
Hi everyone.
I looking for help with diagnostic tool launch crp349.
I buy that, make updating, use once. And next day tool show message like "you serial number is not registrated".
When go inside menu to check that, I see nothing in SN location, when go deeper, under "BOOT" and "DOWNLOAD" stay "unavailable".
So maybe someone have firmware for that, or can help me solved that problem.
At now tool Is useless.
I have Citroen Jumper Edc15C7 with immo off, but there is U1600 DTC. I try to find "68 42 2D 03" bytes, and I found them on 17750 and 177D0 lines, but they are already 40. Does anyone have a working application to remove the U1600 code?
I have an Iveco Daily with an ECU (EDC17C49) that deactivates the cruise control when it goes over 93 km/h aprox.
Is there a way to disable this or increase it to the maximum speed, please?
Hi, I have a BMW 2007 320i with steering lock issues, tried resetting counter etc with tool32, Ista and Launch with no joy,
I purchased a box online which was supposed to bypass the ELV but after putting it in, the transponder coil error comes up, and does not recognise key.
Would anyone maybe know how to turn it off?
Possibly there would be settings on NCS which could do it?
Thank you to anyone that replies
Hello! Whoever helps me with a complete kit of Ista D and P Ilean version 4.51, 4.52 to be with native installation, I will offer them a free license generator.
HI, i have little problem, because i can't change coding in ECU... Can somebody help me with correct file to 2.0 TDI CBAB 140hp and say how i can do it without mistakes? I attached my bench read file. Thanks for every advice.
EDC17CP14
03L906022MA
398757/3611
Hi, would someone be so kind as to make me a Stage 1 + EGR off? It's a Seat Leon 1P1 1.9 TDI BXE. I have the empty cat and a Pipercross replacement filter.
I'm attaching a copy of my file because I've tried others and they don't work.
I replaced a 2017 Audi Q7 transmission with a used one, the car is stuck in Park and will not go into gear, I get a code for "Control Module Locked" which needs programming. I currently have all tools and all hardware to do it but do not have online access to get it done. I have ODIS but no online access, Can this be done?
If it can be done what exactly is needed to get it done?
My customer needs a spare key for 2013 Nissan GTR. I scanned his key and the id chip was 47.
I’m looking around to find the smart key but all are ID46. Also I bought the OEM smart key from the dealer and when I scanned it shows ID46. I know that this key will not be programmed because of different ID.
Is there any other Nissan smart that work for GTR?
have some manuals from when i was a ford cosworth nut , original genuine ford sierra cosworth and escort cosworth workshop manuals (pdf) ( these are the ones with the blue covers that ford dealers in uk sold for 50 uk pounds years ago) . also wiring manual and group A and group N cosworth modifications manuals ,
Hello,
I’m working on 2014 Mercedes GLK250. I have a problem with the ECM, I bought another ECM the same part number and I did cloned successfully by writing the eeprom and the flash. Now the car doesn’t start with the cloned ECM. Is there any procedure that I am missing? I did clone some BMW and VW ecm and the car started, this Mercedes not.
Can someone help me please.
Hi,
Got a Audi A8 D3 4,2tdi, that have been tuned to stage 1 and DPF off. DPF is physically removed but all sensors intact.
Now the engine goes into limp mode after 10 seconds, ingntiton off and restart and the same happpens, limpmode after 10 seconds. Tried to disconnect both EGR in shut state, same issue.
Anyone know what the problem can be?
