Hello, I need help with Fiat Ducato/Peugeot Boxer airbag, came from other shop. Airbag had water damage, they installed brand new airbag unit 00046858203, did some kind of programming, now no DTC but Airbag light is on. I'm not an expert, but i'm pretty sure old file has crash data saved, eeprom chip itself is ok, but there's a lot of water damage, it does not communicate. Could anyone check files to see what is wrong? Thank you.
Hello guys I have a problem with Lodgy 2020. Done odo recalibration with patch, written ori flash back but milage is not counting up. Also range for fuel is not displaying.
Any solution please?
Pls I need help with this dump from outlander 2010.
My key programmer doesn't recognize the dump and keeps giving me "unknown version" even after reading the dump endless time. So I believe the dump was corrupted.
I will appreciate some help to repair the dump pls.
Dear friend, i have a question , if there is professional engineers who may help me .
my customer has a set MAN CATS T427 with key dongle, but it keeps back to the page asks login in information and i am sure the password is right .
the first page is an notice says " unable to connect to MAN server "
here i post the video, anyone who can help me , i would like to pay . thanks a lot
Hello, at a Passat with BMP engine, which enters limp mode because of P2279 error, I need limp mode off. Car works fine and I can't find the air leak that causes this error. Also I don't know where to find the limp mode torque maps. Car has DPF and EGR off. Please help.
Does anyone have original file for Citroen C3 Picasso or has dealt with U0140 there are no other faults in whole car I think its bad remap causing this fault. MEV17.4.2 96 663 191 80
Software:96 790 120 80
Hi to all members i have a problem whit dcm 7.1 delphi citroen..I read in boot mode and remouve egr but after write a file car star work no egr fault but have oil preasure on dash..Can someone help ?
Hi!
I have problem after dpf egr off in 9df marelli. After few kilometers car goes to limp mode- max rpm 2400 and no power.
I tested solution from fixwave, ecudecoder and i have this same problem.
Any solution?
hi guys
someone has experience with iveco 35c13 iveco 2.8 2003 electronics by ms6.3 bosch
i have 2 errors in ecu with symbol of injector blinking on dash
1) no signal from coolant sensor 0000002B
2) no signal from temperature of fuel 0000003F
the van it's in recovery mode
i checked the wiring it's all okay, after i tried with another ms6.3 but still the same....
i thought that some cable came from dashboard for this signal, it's possible ?
thanks guys
[font="MHH Font", Calibri, sans-serif]Hello, friends! Who can help with programming a tecu. Gearbox at2612f i can pay contac me whts +50684633463 [/font]
Hi guys! I've got Mokka EV with suspected crash data in srs module [font="Market Sans", Arial, sans-serif]9835661480[/font] . Lots of errors on traction battery switch, electric drive etc. etc. Strangely there's no airbag light on the dash! But from what i read online, srs module sends crash data message to traction battery module and turns the relay off (there's no pyrofuse in Mokka) to disconnect th ebattery.. Can anyone please check whether there is a crash data in the module and perhaps can clear it? Thanks a lot!
I have been trying to get a 2017 Ford Mondeo PSCM / EPAS out of the U3000:49 dtc. Module is basically locked by this DTC.
I have tried to delete DTC, module reboot, module remove/install procedure and also did firmware update with forscan but could only find the same software as already present.
After some reading i realised that this U3000 dtc wont go away and i have to do a full firmware flash or replace the complete rack.
Flashing firmware might not solve anything, it might also go straight into U3000 again but the cost of replacement makes it worth a shot.
I have seen some threads on removing the eeprom and reading/writing in a burner.
Are there any other options? Will gladly pay if someone can provide a solution that does not involve
unsoldering the eeprom.
Hi, I have a problem with my 2023 Kia EV6. The issue is with the front parking assist system. I’m getting a fault indicating that the front inner right sensor isn’t working.
I’ve already checked the wiring and even swapped the sensors around, but the issue remains—the front inner right sensor still doesn’t work. Since the parking assist sensors operate on a LIN bus, I suspect it might be either a faulty sensor or an incorrect plug.
The car was involved in a crash, and it looks like the plug for the front inner right sensor was replaced. I suspect it might be the wrong one.
How can I determine the correct sensor and plug for that exact location?
Thanks in advance for your help!
Hello, I am looking for a link or torrent file for xentry Truck 2023.09. This version worked for me with my vcx se and the current version 2024 Truck unfortunately I can't pair vcx with xentry
