The attached files contain the software, license, VAS 5054 device setup and instructions. I am sharing the complete set with you. You can install and configure it yourself.
Description :
ODIS-Engineering- allows you to "flash" control units without
official access to the server. To do this, simply specify the file with the desired firmware. ODIS Engineering also allows you to change encodings and adaptations. But there is no guided diagnostics in the engineering ODIS, it is available only in the ODIS Service.
FREE FOR EVERYONE!!! To receive the file, please send a message in PM after the THANKS and REPUTATION mark!!
If you are interested, I am waiting for the status! In the near future we will also share ODIS Service 7.2 and the VAS5054device setup.
NEED help i lost dump from dash eerrom touareg 2016 dash bosh eep 95320 cant read eeprom anymore
i used china digiprog to read eep .after a clic on V message says virsion not suported .then i put eep on vvdi to read it nothing i try to read it many tools the same probleme
hi friends, i need dpf off with cheksum dcm3.2ap ssangyong, already try 2 files when write with kess not start write ori file and start again.thank you
Hello members. I am asking for advice on an airbag control unit 610796100 8200854865 of a 2008 clio.
I have several dtcs present and in diagnosis I cannot delete them (impossible to execute the command).
I read eeprom 95640 and fixed the dump with nyo. But nothing to do, the control unit does not respond and the dtcs are still there. What would be the solution? Should the control unit be changed in this case?
Hi. I need to replace used bcm2 for a6 2016. I know the best option is to use new bcm,but I need to do it with used one,it has the same numbers. The easiest way to do it? I got only 1 key. I have IM608 and odis with geko. Any help? Thanks.
hi got MB W230 SL500 with lost ezs. Dont ask how, but there are no ezs So i bought used ezs with key and now need to sync esm with it. Have both dumps, maybe someone can help to prepare file for esm or ezs..?
I have a car with ecu died
the car already have not immo box
key ring removed
i already do immo off in eeprom but i think need to be done in flash too
because the car with a ecu from donor want start but shuts down
Hello, i have problem wih this car CAS system,I can't access the CAS diagnostics, but the ignition turns on, the steering lock works, could it be a CAS flash, eprom problem? I can't access the CAS diagnostics, but the ignition turns on, the steering lock works, could it be a CAS flash, eprom problem? file attached
I have 1 Volvo airbag modules with very stubborn faults.
I have tried several methods of clearing crash but this is the first time i experience anything like this.
Can anyone please help resetting these or if you have a virgin file so i can compare to that would be great?
& P31406630:
B10A202 - Crash input general Failure
B10A206 - Crash input general fault algoritm based error
B10A215 - Crash input general electrical fault - circuit to battery or open circuit
Thanks for all the help,i will ofcourse leave rep + thanks for the help.
Hello, Dear MHH members,
Wondering if someone can help me sort this out without getting a second key cut
I was called to no start on a VW GOLF 6 PCR2.1 Engine ECU issue someone put cables wrong when jump starting I was told by the garage...
Supplied another ECU got another member to do IMMO off and car started and have gears it Is DSG transmission.
ECU part no. 03L 906 023H same as DONOR
Cluster part no. 5K0920960N UDS
VIN: WvWZZZ1KZAW275504
Current situation:
NEW USED DONOR ECU FAULT 1: "P1570 00 ECM Locked" car starts fine applied IMMO OFF from another member of the forum.
When I checked the car first, I noticed 1-2 on the cluster but didn't take any notice...
I cannot remove the "1-2" no faults in the Instruments I think that Cluster is in programming mode for keys and I cannot finish it without second key... :-(
The problem is that I currently have only 1 key for the vehicle
Is there any way around it before I order another key?
Thank you in advance
TOOLS AVAILABLE: IM508+XP400, VCDS, VAS5054a, ODIS S 7.2 offline, VCP5 clone