I have attached original files and ID read with Kess3 in bench mode.
I have tried multiple solutions but all cause issues with ESP, boost & gearbox control, on stock file everything works normal but with adblue & DPF faults.
Hi!
I have an Audi A5 2019 with 4N0907129KH with G85 calibrating problem.
I have been working on steering wheel and now I have value of 819 degrees.
I dont have any error on chanel 16.
Can someone help please!
hey guys i have a 2024 porsche macan GTS here that i had a whole disaster with when trying to program the keys, so i finally ended up getting it working, i even got a second BCM same part number and tried to read it and it did the same exact thing,
to fix it i ordered a new 5m48h chip from alieexpress once it got here i partitioned it, programmed my D-Flash but my P-Flash was corrupt, i ended up downloading one from a 2014 cayenne from here and it worked, however now my problem is the dash says i have an issue with me left front side marker and left and right turn signal circuits, but i dont they are totally fine and work, but the errors keep popping up, im wondering if it has to either do with the P-Flash or if maybe i didnt solder the chip on good enough or something im not sure im going to pull the bcm now and check and see if its my solder work or anything but just in case im hoping i can find a p-flash from the correct bcm
Hello !
Can anybody help me with a code for Renault Carminat Becker radio ? Part/Model [b]BE7401 (8200097398)[/b]
Manufacturer [b]BECKER[/b]
Serial number [b]55002921[/b]
Hi this ECU PEUGEOT 307 2L essence car start and drive good without EGR, but when i plug in it goes crazy
need 100% EGR OFF solution please
i heve dtc P0403 P0404 P0406 PLEASE MAKE OFF
Hello
I have bmw E60 with no ignition (mechanical key), no errors on CAS, fuses and relays checked and I susspect that it's a CAS problem.
I attached the flash and eeprom of CAS2 2K79X, part number 6960978 5WK47995
Can somone have a look and see if it's eeprom of flash corrupted ?
Thank you so much!
1. TPMS light on dash
2. Fault "01840 - Antennas for Tire Pressure Monitoring 004 - No Signal/Communication" stored in [65] - TPMS module.
The antena on the underbody under the spare wheel was replaced, TPMS module was replaced and wiring checked. Wheel sensors are all new just replaced and cloned from original when new rims installed. As far as I know IF the receivers in the wheel arch was the issue I should have different fault stored. Maybe someone can help with this?
Hello can someone help me with file for Yuchai generator
0281020503 A50000-3823351 EDC17 YCECU-A38 ECU. Flash on old ECU is damaged so I can't clone and I ordered brand new ECU so. Starts and stops so I figured I need to write working file in ECU
I am trying to get a BEV 2024 Fiat 600 driving after a crash.
It was a fairly light crash but did set the airbags off
I have FIAT WiTECH.
I have a new airbag ECU but have not installed this yet. It will ask for a Technical Information login and I do not know what this is, I have signed up to multiple sites but none seem to work, any ideas?
But also it has fault codes for HV positive contactor and also crash:
EVCU P1AEF-68 High Voltage battery pack: Activation of the crash sensor by CAN bus - Event information Active
EVCU P0AD9-13 Hybrid Battery Positive Contactor Control Circuit/Open - Circuit open Active
I cannot seem to clear the crash event. If you press:
Rehabilitation TBMU after crash event
You just get a negative response with no reason why.
Fiat dealer thinks it needs a new airbag ECU first, but I'm not so sure.
Also the battery was nowhere near damaged so I have no idea why it has a positive contactor fault.
Fault codes don't seem to clear easily with pass thru though
The TMBU did work ONCE and after that it won't go through the proceedure again
