HI ALL ,
I NEEDED DPF/SCR/EGR/NOX OFF
I USED MY NORMAL TUNER BUT FILES ARE NOT SUCESSFUL ,
VEHICLE IS IN LIMP MODE , WONT GO PAST 20MPH
WONT REV PAST 3KRPM ISH
CAN ANYONE HELP ?
TIA TO ANYONE
This was the 1st file he sent
(Today, 02:41 AM)cwarren99 Wrote: HI ALL ,
I NEEDED DPF/SCR/EGR/NOX OFF
I USED MY NORMAL TUNER BUT FILES ARE NOT SUCESSFUL ,
VEHICLE IS IN LIMP MODE , WONT GO PAST 20MPH
WONT REV PAST 3KRPM ISH
i have MD1CS001 for G30 i did adblue off , the car starts fine, but check engine light always on with dtc 272000 , i did DTC off but no luck , no fault code and engine light On, any solution?
hi guys need egr off dtc is P0403. After deactivating with automated program dtc P0000 is present.
can someone help out? Im ready to pay for coffe for a working solution but not 30-40 Euros.
Hello. I searching maybe who selling or can share with any pq25 pq35 3d flash in .bin format. I accidentally flashed wrong frf file, and now in 3d cluster black screen
When trying reflash back, vcp shows bad datablock length, becouse black/white screen have 15 data blocks, 3d 18. Maybe someone have this one flash in archive saved ?
Hello I hope somebody can help me! I deleted the P3060 Code via Stagex, but there is still the massage on dashboard "Engine fault: Repair needed" with the wrench-light.
There are no fault codes in the engine ECU, but sometimes U1318 (Connection Problems with BSI) after reconnecting the battery.
The engine is in good shape and sounds good, but is in limb mode and does not pull.
The BSI has a fault code B183F.
Do you have a solution? Of course i would pay. Thank you very much!
He leído la ECU Ford Transit Connect SID206 con FLEX y necesito hacer IMMO OFF.
Datos del vehículo:
Marca: Ford
Modelo: Conexión de tránsito
Motor: 1.8 TDCi
Código de motor: Duratorq (D/RAFA)
Cilindrada: 1753 cc
Potencia: 66 kW (90 CV)
Año: 2006
Tengo la lectura completa de la ECU y puedo compartir el archivo si es necesario. Agradecería mucho si alguien pudiera ayudarme con la modificación del archivo o indicarme la mejor manera de hacerlo.
My name is Doni, and I hope you are all doing well.
I own two Liebherr 566 Wheel Loaders and one Liebherr 580 Wheel Loader, and I am interested in the LIEBHERR LiDIA software. I would like to know if it can be installed on any laptop or if there are specific hardware requirements.
Additionally, I would like to ask whether I can purchase only the 9-Pin Diagnostic Kit separately and use it with the software, or if it is exclusively designed for a specific Liebherr system.
If anyone has the software available for sale, I am willing to buy it.
Any insights or offers would be greatly appreciated.
Thank you!
Original ECU is damaged physically in a way that read is not possible anymore. There is a spare ECU with exactly the same numbers from a donor car, would any of you be so kind to either virginize the used ECU to be able to set it up in the car, or switch off the immo?
Friend has problem with his M57. He swapped it to E30 and went with EWS emulator. However car won't rev past 3200 RPM. I tried following maps:
- EngPrt_trqLimDA_CUR,
- CoEng_trqLimErr_CUR,
- CoEng_trqLimErr1_CUR1-4
- changing max DA state speed to 0 via VehDa_rVnMax_C
Nothing appears to work for this car. Where should I look for this RPM limiter? Thank you in advance for any recommendations.
Attached file of the car + mappack I used to raise couple torque limiters
hello all members here,
I search in forum xdos xentry version 12.2021 or 03.2022 , but all links i found is down
For where i can download? Can any share link please?
Is there acronis image for all programs in one ?
I buy my first c4 and need install all
Thanks alot !!
I already make this ecu dblue off but i don't now why my tool ( Foxflash ) not make tprot off when write this file So when start the car after writing it's start many times after that stop starting the engine at all
Could anybody do tprot off for this Ecu manually please
I have a kess3 but it doesn't write the areas I need. Dfox does write the correct areas but i dont have one. Does anyone know if there is another tool that writes these same areas to be able to clone a ecm?
I bought a used dashboard for my bike. The mileage is much higher than my bike. Is there a way to lower it or reset it? It has no screws, it is a pressed unit, so if there is a method to read and write via pins, I would be very happy if you could share it. Thank you.
