i have a scenic 2017 and i dont have no errors on ecu but when i erase the ecu dtc, the abs light is off untill i start the car....i think there someone have made a dtc off or something
Hi I need help finding boost sensor linearization map on this car or ldr maximum negative threshold, car has underboost and boost sensor when car is off showing 817mbar which cant be ok.
Hello all My W205 crank but engine not running Have Fault code P062700 , P062713 that mean the output for the fuel pump has an Electrical fault or open Circuit im already change Fuel control module (second hand ) same part number but not yet new Coding for my car Is it related to not coding yet? Or do you have any other suggestions?
Hello!
I have these two files for the same car. Can you please tell me if v2 is safe to write, or what diference have been made since v1?
I know there is not much gain, i'm just curious if the v2 map is better or different (i am using v1 and it's clearly better that stock). I will attach also stock file.
Thanks!
Need some help with this one. I am having problems removing DPF and SCR (AdBlue) from a 2022 Fiat Tipo 1.3 MJD.
Made the resets and cleared all the messages, filled the AdBlue tank, after being sure that no message was on the car, flashed the file. After about 50 Km's, car come back with AdBlue message and no start if restarted. I've tried with AdBlue module connected and disconnected. A few solutions were tested and none worked: Swiftec, ProjectX, Fixwave, ..
hi guys you can also help me with a software modification to obtain a power of 150 hp. I changed the ARL turbine and MAF sensor on a 1.9 tdi engine code BRU. I am attaching the original files and the one made by the person who sold the maf turbine putty. Thank you!
hi all
i need a correct dpf off for chevrolet captiva 2.0 VCDI
I have made same ecu before but this one the DTC P2463 still on and the engine is always in limp mode
Hi to all ! I have a GLA H247 250e and i want to retrofit with original parts the illuminated door sills.I have bought the illuminated sills and wiring harness but i dont know if i have to connect it to the door light or it is a module handling them.Has anyone the doc for the specific procedure?Thanks a lot
I'm trying to do an IMMO off using Neuro Suite.
I bought their tokens, loaded the file into the tool, and the tool then asked me for an "MCU ID".
I did a bench read with Ktag in service mode, but Ktag does not show the "MCU ID".
I then tried using PCM Flash to identify the ECU. It showed data, but still no MCU ID.
I emailed Neuro Suite support, explained the situation clearly, and attached the logs.
They replied quickly, but their reply was useless — they simply said:
Quote:"You cannot use PCM Flash to do IMMO off on SIMOS 8.5, try using MPPS."
It was clear they either didn’t properly read my email or there was a translation issue.
Regardless, I replied back with even more detail, trying to be as clear as possible.
Following their advice, I even tried MPPS to grab the MCU ID (even though I knew it wasn’t exactly what I needed).
No luck.
I understand it’s the weekend, but it honestly feels like a brushoff.
This isn't the first time either — years ago, their launch tool bricked a MED17 ECU on me, and again, they offered zero help.
At this point, I’m done with them. I’ve had three accounts, three different emails, and spent over $2,000 with them — and this is how it ends. Question:
Is there anyone here who can do a tested, working IMMO off for a SIMOS 8.5?
I'm willing to pay a fair price for a real, working solution. Thanks for reading.
i have schaudt lt 632 , control panel from mobilehome, the battery was change and now is on display just U----, i think its somethig with software, does any one can help me or can repair
please help
![[Image: i8YeQEr.png]](https://i.imgur.com/i8YeQEr.png)
