Hello everyone. Problem with Ford s-max 2011. The problem is that the instrument cluster and the climate control and radio do not turn on, but the car starts without problems. Errors in the control unit bcm U0155 and U0164. Can anyone tell me where I can look?
I got a car in my shop with no working keyless access and start. No codes in 05, 09, 25. Verified key, coding, and parametrization - everything looks good. Added new proximity key - same thing only remote is working as it should but when I press the start button says key not detected. As soon as I touch steering column coil with car starts right up.
Kessy doesn't have any sights of water. All fuses are in place. Don't see any aftermarket bs too.
Hello all, I am trying to find the data matrix code for a 2020 Mercedes Benz 167.159 GLE 450. I am having issues getting the QR code data from the headlamp. The vehicle came in with a water damage module, I replace the module with a brand new genuine unit but its showing B223955 fault due to no coding present.
I am a new member in search of experienced advice. I have a 2005 w220 s65 AMG. Recently the car would not start. I diagnosed the issue to be the ESM on the shifter. I purchased a new shifter with same part number. The car now starts. I know this module needs to be coded to the car. However now I do not have communication to the module. Old module had communication. This installed used current shifter is sporadically actuating the Shift lock solenoid. This is possibly how the old shifter failed. The shit lock solenoid even actuates while driving sporadically. Has anyone encountered this issue. All wiring seems to be intact. Good voltages, can voltages good, ground good. Break switch is new, and through esp actuates as it should. What could be triggering the shift lock solenoid to actuate? Is it possible that the ETC is faulty?
Attempting to renew a W216 2009+ EIS. Calculated key password and erase password on both CGMB and VVMB. Both fail to erase. Previously both tools will often say that they failed when they actually succeeded but this is not the case in this instance. It is NOT a dealer EIS according to CGMB. Any ideas?
Thanks.
EDIT: Tried Autel as well for the hell of it. Also failed.
greetings, I took apart the alarm clocks on the Škoda Citigo and cleaned them, after assembly, the fuel gauge in the off position shows a pointless position very low and the tank shows 3/4 full. I also noticed that the level in the tank does not decrease while driving. can anyone advise what to do with it?
Hello once again friends, I have a problem on my girlfriend's car. P20E8, it seems it is the adblue tank? I have manually inspected and tested adblue injector, it is clean and looks good and sprays adblue.
Now I am left with what solution to choose.
Buy a tank and fit it myself, delete codes and hope car is okay which will cost me maybe £800 if I do it myself or less if I get a second hand tank (second hand tank around £300 but risk this fault again soon)
Or use a tool and adblue off if some kind member could help with this.
So what tool can do this? (Clone tool, as I will probably not use it again)
Hi. I have a problem with a 3008 hybrid4. The car does not start. As soon as you turn the key, the display shows "engine fault".
I have no errors in the engine control unit. In the HCU2 control unit I have 20 dtc that it does not erase. I suspect that the ecu is blocked.
Can anyone help me? Can this ecu be revirginized? It should be a bosch HV17.4.1
Hello.
Seat Exeo 2.0TDI multitronic NDJ
I have a problem with tcm which is dead. I could not find the same driver designation, so I bought with one letter difference from A4 B6 1.8T. Thanks to the photo of the error codes in the old controller saved in the phone gallery, I know what the software number is
Dead tcu - 01J 927 156 HT ( software number from vcds 8E4 910 156 N )
New tcu - 01J 927 156 HH ( software number from vcds 8E0 910 155 K )
Unfortunately I have no option to clone this controller. Can anyone suggest how to add it to the car ? Or maybe has a software file that matches the data given above. I attach a description of the error codes from the new controller. Greetings
Hi everyone! Can anyone instruct me on how to purchase or get FSC codes for my Kafas on my 21 X5M? I had to buy a new camera unit as mine was stolen after it was in a wreck.
The car sometimes works, sometimes doesn't. The error codes it gives are listed below. Do you think this is a BSI (Body Control Module) issue or an ECU (Engine Control Unit) issue?
Peugeot 308 2017
have a nice day
![[Image: lIEqeuoKVORQ.jpeg]](https://r.resimlink.com/lIEqeuoKVORQ.jpeg)
![[Image: CTu3hQ.jpeg]](https://r.resimlink.com/CTu3hQ.jpeg)
![[Image: CH1tiUoK.jpeg]](https://r.resimlink.com/CH1tiUoK.jpeg)
