LAUNCH X-431 SmartLink C HD Lite Expansion Package for 8 inch X431 Diagnostic Tablets
Price: €582
LAUNCH X-431 SmartLink C HD LITE expansion package consists of the X-431 SmartLink V2 Heavy-Duty diagnostic module, commonly used non-standard adapters, and a heavy-duty vehicle software package.
This expansion package is designed for professional heavy-duty vehicle diagnostics, offering broad compatibility and advanced functionality for workshops and technicians.
Product Features:
Dual-processor Cortex-A7 + Cortex-M7
8GB RAM + 256MB storage
320×480 resolution display
Multiple connectivity options: Bluetooth, Wi-Fi, USB
Compatible with X-431 PRO series (8-inch tablet),
Full-system diagnostics: Read/Clear DTCs, Read Data Streams, Special Functions, Actuation Tests.
Hi,
I have a problem with an Opel meriva 2017, the problem is on the bcm 39013500, every 30-40 starts the odometer reset at 76500 and the car won't start, I've seen that this is a common problem on this bcm.
Does anyone know how to repair this bcm or know somone that can repair them? I have all files of the bcm in case.
Thank you
hello everyone, i did a DPF+EGR delete on the Mito 1.3mjd from 2010 and now it smokes a lot and smells heavily like unburnt diesel, only after it is at perfect working temperature is wen the smoke goes away but still smells like diesel.
It has 1 new injector and all other 3 were checked and are ok, glow plugs, turbo and basically everything else was checked besides the cylinder compression.
Has this happen to any of you, or do you know any possible solutions?
ori file and DPF EGR delete file attached
I need help to program Engine speed for PTO by EST. I have never used EST before so just want to check some of the operation is possible to do by EST or not.
Hey, got a 2018 XC60 T8 the hybrid battery will not charge, tried numerous chargers with no luck, it does charge using regenerative braking. Believe it to be the OBC unit is faulty, does anyone know if these units require coding and can a second hand part be used?
Hello everyone, looking for solution without parts cannon for this vehicle. Long story short battery got dead after that fault code appeared in PCM P0513 invalid skeem key. VIN number is correct in all 3 modules (PCM,BCM,RFH) did proxy alignment it went through no problem. tried to reprogram key with no success. I found only one thread on this forum but solution wasnt disclosed. Ready to pay for working solution. Also found online info that eeprom getting sort of corrupted with low voltage in PCM and theres 2 ways to solve it, either correct it or put the virgin dump in PCM and then reprogram it. Please advice. Thank you!
Hi, i am wondering how to disable damaged navi unit(placed on left side of trunk)
most loop will be needed for sure,
but if possible i would like to code it out,
none of modules reports dtc related to navi so far, so i think that fa remove,may be sufficient, but i can`t find fa list that fits
somewhere i saw that $6xx are navi related,i attached fa list red from the car
This dashboard was previously repaired by another company. It's now here. I've checked the MCU soldering irons. They're correct, though. I've resoldered the entire microcircuit and surrounding resistors. The problem I'm seeing is when powering the panel on the table. Without using a CANbus signal, I already have strange digits on the display, and I think it's a problem with the MCU's SW.
However, since it was previously repaired, I can't tell what the panel's reference number is because they removed the label from the panel. I'm attaching the MCU reading from the panel. I hope someone can help me. Thanks.
I recently replaced my TTV parking heater with a slightly newer TTV VEVO. Yesterday I decided to check what the other firmware could be uploaded to the old one. Unfortunately, I uploaded something wrong and the heater stopped working and it was no longer possible to upload another firmware. Inside is MC9S12DG256MPVE, I connected XProg. The processor is not protected and I managed to read it on 4 wires. I found a dump of a similar heater on our forum. After uploading it via Xprog, it could be diagnosed, although it showed the wrong part number and strange errors, and the control did not work. I think the downloaded dump was from the EVO version. I uploaded the correct firmware via the diagnostic adapter and although the FW version changed, the part number, strange errors and bad behavior remained. Well, that's a bummer, I need the right dump, but there is none.
I smoke some and I had an epiphany. After all, I have several of the same heaters, each with some defect, but in one the board was functional. I copied the dump and uploaded it to mine. Now it works. Errors are good, tests have shown that everything is as it should be.
I found a dump on this forum, although it was inappropriate but helped to repair it. Since there is no such dump anywhere on the internet, I decided to share it with you. Free is a good price.
The file comes from the Webasto Termo Top V (non-EVO) Diesel furnace installed in many VAG vehicles.
If you have any questions, feel free to ask. I will try to help.
If you downloaded this file and it was useful to you, press THANKS at the bottom of the page. I will know that what I do helps others.
Hello, recently purchased a c350e. Currently experiencing several faults. The car Heard kinda hard, e-mode and eco doesn’t work and i get a yellow malfunction message in dash.
Currently have these fault codes scanned with Star diagnosis:
B21DF71 The relay «of decoupling of starter battery” has a malfunction. The actuator is blocked
P1D8C92 The switchover valve of low temperature circuit 1 has a malfunction. The function or instruction is faulty.
P052E71 The valve for crankcase ventilation has a malfunction. The actuator is blocked.
Is this the starter motor causing the battery error or a module? Any help is greatly appreciated.
I'm looking to buy a working and stable version of:
– MPG (Map Pack Generator)
– OLS Map Finder (or similar software that helps identify maps and switches in WinOLS)
I'm NOT interested in StageX, ECM Titanium or generic software.
I'm specifically looking for something that gives accurate map definitions and switch locations in WinOLS 2.24.
If you have it and are willing to sell, I'm ready to pay.
Payment via PayPal / Revolut / crypto – no problem.
I'm looking to buy a working and stable version of:
– MPG (Map Pack Generator)
– OLS Map Finder (or similar software that helps identify maps and switches in WinOLS)
I'm NOT interested in StageX, ECM Titanium or generic software.
I'm specifically looking for something that gives accurate map definitions and switch locations in WinOLS 2.24.
If you have it and are willing to sell, I'm ready to pay.
Payment via PayPal / Revolut / crypto – no problem.
Hi members can someone add for me a key to this Dump Denso ECU 7A-FE 89661-05210
My Chip data is Tiris 4C
IDE: 00 00 00 00 C5 34 40 93
Live data: 7E 93 40 34 C5 00 00 00 00 13 67 7E 00 00 00
eeprom is 93c56 All keys are lost. If immo off is available i would appreciate
hi guys, i want to clear crash data from veoneer 9849207580 for mokka 2024 electric car, i'm new to this work, i own Autel608 pro +xp400 pro, but after researches i believe theses tools won't help ,
my question which tools i have to use to be able to read and write, (i will use online service to clear the crash data) read and write will be enough for me for the time being
thanks in advance
Hello, does anyone have solution to repair airbag module for 2024 Mazda 3 part number bhpd57k30b please? Or a pinout possibly to read file and see if someone can clear it
I need to close 48v battery relay to start charging the 48v battery via 12v. I dont have ODIS and my esitronic dont have this option.
I have launch but it says that I need access approval, perform login.
Does anyone here have the password for it?
Its 2018 Audi A7, diesel/electric 210kw
![[Image: 25041017442717843133.jpg]](https://www.eobdtool.co.uk/upload/pro/25041017442717843133.jpg)
