I have a 2011 Corsa D 1.0 EcoFlex which isn't reading any data from the MAF. We have checked the fuses, tried a brand new MAF and also swapped ECUs but still nothing.
Does anyone have a wiring diagram for this please? I can only think it's a wiring issue after trying everything else.
I have changed flywheel on a skoda 1.6tdi dsg 7 speed
And now it bangs in drive
Basic settings will not go througt with error 255 101
And error codes
P177d torque to high
P072b unable to put in reverse
P1895 oil pressure drop
Could you give me the contact details of the author, email. I'm looking and so far without any results. I would like to buy access but I don't have crypto. Thanks in advance
hello, after a bad battery and flash write not completed, i need this software!
Renault Master 2023 IC flash
id 248B332245R
Supplier 436F6E
Boot ed 250460937R
Partno 248096232R
i attach completly free for whoever needs it
mine was a3c0707450700 but it worked
Hello everybody,
Currently Im fighting a battle with VW Caddy 2.0 2016 with ,MQB DQ250 DSG transmission, car originaly came without reverse gear, replaced transmission with junkyard one and also cloned TCM with FLEX..replacment mechatronic numbers didnt match exactly car would only go to 2 gear and then slip (turning car OFF and ON would fix the problem (also only to 2 gear)
We tried different transmissions and mechatronics, current mechatronic has all numbers matching
Fluid level is correct we put in oil
(In ECU DPF and EGR are turned off)
transmission is 02E, I did all the BASIC SETTINGS expect clutch adaptation (062) as it throws ERROR, could that be the reason for slipping out of gear and not switching?
I dont have a lot of experiance with DSG transmissions so Im deeply sorry if I asked a dumb question.
Thank you all.
Hi everyone,
I'm looking for a DAMOS file or a reliable solution to remove the speed limiter (Vmax off) on an ECU. If anyone has something or can point me in the right direction, I’d really appreciate it.
read by flex magicmotorsport boot read
Thanks in advance for your help!
Have a great day.
Hello.
I need help with EIS w220 2205450308 on 1D69J.
I wanted to make a new key.
I desoldered the processor and read the Jtag smok in the adapter.
During reading, the processor was damaged, all content on FF
After soldering the processor, EIS saw the key and the ignition turned on but did not start the engine.
Error P1570 - No access to start from FBS.
I read the key password from the NEC key.
I generated the EIS deletion password.
I can't do Renew EIS via IR I also can't save EIS data (keys) via IR that I read via OBD (on the table) and via IR.
Is anyone able to repair the file with keys and password for 1D69J?
Attached is the file that I read via OBD and IR to prepare the key
hello i have a duster model
Duster II
Vehicle_type
HMAB
Vehicle_fabrication_number
A003535
engine
K9K658
engineNo
R049154
Gearbox_type_and_suffix
TL8015
i have intermitent power to glow plugs. and sometimes eror code 038013 Preheating unit diagnostic connection open circuit. i need a schematic for the wiring.
checked the wiring from relay-ecm and are ok. replace the relay, same problem.
witch pin is for diag and for control ?
Hi everyone , need full backup for BMW e61 , no communication with ECU.
Or MPC + Flash.
Thanks for attention, and have a nice day!
Actual files read on attachment, thanks for attention!
Hello
I ordered an IProg v777 clone from ali and it arrived but it doesn't work.
No matter what I click, it says "Programmer not connected".
Driver installed
I tested Iprog 85-78-55 software but none of them work
Has anyone encountered such a problem?
What can be the solution?
