tried to viginize the file my self, i followed the procedure to learn the ECM , shows successful on Autel , try to start the car it wont start.
and the status of the ECM is not learned again.
can some one help with viginize the files, i will post eeprom and Micro
Hi team, I would like your help regarding a problem of data loss from a QM6 meter following an intervention on the dashboard. The meter has gone completely black but still communicates with the diagnostics.
Hello, I have a client with a Hyundai HX220 machine with a CM 2350 ECU. The ECU is defective and I need to clone it. I bought a virgin ECU on AliExpress but I need to know how to clone the ECU. I was able to get information with KT200 but only from flash. Does anyone know what the EEPROM is in this ECU or if it has one? Or is just cloning the flash file enough? Greetings, I hope someone with experience can help me.
Hello I have a problem with a BMW 3 e91 with CAS3....the car only starts if I reset ELV errors with diag, or unplug the CAS and plug it back in. In diag I have these errors in the CAS unit: A0AF: CAS processor A11E: ELV defective A0AA: control unit defect Could it be that this CAS unit is faulty? Or is the problem in the ELV unit under the steering wheel? What is the best solution in these cases? Thanks
CAS3 61.35-9217853-01 2093007219 5wk4 9515ABR
Ps. I read the eprom and flash of the cas, but I have the doubt that I have not read it well, even if I have made sure and the connections are correct. Attached are the files
================================================
Prepared special Nissan Consult III Plus mod for Nissan GTR cars.
Requires testing with real cars. No GTR smart card is needed. Software based on CSR v.51
Demands:
Nissan GTR cars;
High quality J2534 adapter (API 04 or API 05);
Your time and desire to participate.
Recommended to use adapters with at least 2 CAN and K-lines recognition, as Scanmatik, Autel, Chipsoft, DiaLink and etc.
Best results were detected with cloned or original Bosch VCI (as clones of MDI, MDI2, JLR and Ford, not tested), Cardaq and Mongoose adapters. Nissan VI2 and VI3 hardware also suitable.
(May 10, 2024)
What are ready:
================================================
FREE SOFTWARE
================================================
1. Good working version of NERS software, based on Ners v.3. FOR FREE (J2534). ReProgramming database files v.224 also free.
It's emergency tool and need knowledge to use. Don't ask me how, else i'll ask you for money )))
Easy use included installer file. Then replace archived folder in Program Files (x86) with folder name correction.
If you use 32bit Windows, then correct paths in *.bat and *.ini files.
There two builds of Ners. Build v3 is "classic". Build v8 and v9 much faster.
Use Ners v4 original installer. Run once original version of v4 NERS and close. Replace the installed program folder with the folder from the archive. Everything is ready to use.
2. 82.50 for VCI <= Press HERE
Patched Consult III Plus software v82.50 (Last official for J2534-1) (Mid 2018) for self install. Full ready for offline programming and codding
Please leave your feedback in MHHAUTO forum. Thanks and Rep+ very recommended. Check compatibility of your adapter and let US know.
C3P v.82.50 works well with cars without CGW
This is all before 2018. Nissan started installing CGW in the second half of 2018.
Cars with MODEL YEAR (not year of production) newer than 2018 (2018+) have this ECU, and 82.50 can work with newer cars only in single ECU diagnostic mode.
Full functional version for J2534 VCI mode conversion in attachment, test your adapter and leave your feedback in thread!
Particularly smart comrades are recommended to install the ignition emulator themselves.
===================
Original official version of late actual C3P also available IN ATTACHMENT. Don't forget <<Thanks + Rep>>.
===================
================================================ Consult III Plus Mods v245.10 +PPlus collection (4) based on 244.5 + EU patch v.88 READY
For: Mongoose Series(Nissan, Nissan Plus 2, Plus 3 = MFC3, VW2, GM3 and etc.);
Cardaq Plus 2/3/4;
AEZ Flasher 3;
Nissan VI2, RMN-VI;
Bosch MTS-6531. TOPDON devices works, programming speed slow;
Bosch KTS350, KTS560 and KTS590 must works according specs, but not tested still. Added support for VXDIAG adapters. VCX VxDiag SE, FD, DoIP tested without VxDiag Nissan license. VCX VxDiag NANO compatible with software, but still waiting for test results. ( Supports CGW unlock-open. Tested only on J12, T33, B18 so far)
Hi guys! I have a problem with a customer's Chrysler 300c. When the car gets wet on the front right side, that is to say from the driver's side roof to the fender, the car no longer starts and gives immo problems. From what I know the car has already been to several garages but the fault has not been found. There do not appear to be any water infiltrations or visually damaged wiring, and the strange thing is that if the car remains dry or wet in other places, it never has problems starting, furthermore if the car is on and gets wet it works correctly until it is turned off and then does not start again. Has anyone already experienced this? Advice?
bonjour a tous j'ai un probleme avec un renault kangoo dtc000292 et dtc0002f6 la voiture na pas de puissance la pompe hp chute en pression en charge mais pas a l’arrêt si quelqu'un connait une solution merci
Can someone help make immo off for tis 95160 eeprom on Sagem S2000PL ECU?
I only find solution for 95080 in database, not for 95160.
And also I can't manage to communicate with the ECU with my tester on the bench. Does anyone have a schematic for this model as it seems to be a little bit different.
Hi everyone , need help with tqmon off in kia stinger , i do st1 , but car has limp mode and tqmon dtc.
Can someone help me please with this?
Ori file in attchmant.
Thanks for attention and help
i need a good solution for Temic CRV2.0 EGR off + Stage 1 + DTC off and checksum
the car is W211 2004 4 litre V8 Diesel
ECU : Temic CRV2.0
DTC: [font="MHH Font", Calibri, sans-serif]P2026-001 and P2038-002[/font] [font="MHH Font", Calibri, sans-serif]Flash is AM29F400BB[/font]
Has anyone had issues whit nox recall my phaeton wont accept old file back or original fails to flash every time but new nox recall file writes back no problem
![[Image: GTR.jpg]](https://i.ibb.co/hF3mJR7/GTR.jpg)
![[Image: 974ac75194178ee0bc99f68bbcb09936.jpg]](https://i122.fastpic.org/big/2024/0122/36/974ac75194178ee0bc99f68bbcb09936.jpg)
